Cold-Formed Steel: BP/LBP Bearing Plates

Bearing Plates give greater bearing surface than standard cut washers, and help distribute the load at these critical connections. The BP1/2-3 and BP5/8-3 are available uncoated or with a hot-dip galvanized (HDG) finish.

Material: See table

Finish:

LBP, LBPS & BP5/8S - Galvanized;
BP7/8-2 - Zinc Plated;
BPS, BP - None.
BP's may be ordered HDG; LBP and LBPS products may be ordered ZMAX®; contact Simpson. See Corrosion Information.

Installation:

See General Notes.

roll over images below to see larger image


BPS (LBPS similar)	BP (LBP similar)	Typical BP Installedwith a Bottom Track Anchor Bolt

Standard cut washer required with BPS1/2-3 and BPS5/8-3 (not provided).

					Legacy Reports
	IAPMO ES ER	ICC-ES ESR	CITY OF LOS ANGELES	STATE OF FLORIDA	ICC-ES NER	ICC-ES ER	ICC-ES ES
BP	See specific model numbers for code listings.
BP1
BP1/2
BP1/2-3	Prescriptive code: Products which meet prescriptive code requirements.
BP3/4
BP5/8
BP5/8-2	Prescriptive code: Products which meet prescriptive code requirements.
BP5/8-3	Prescriptive code: Products which meet prescriptive code requirements.
BP7/8
BP7/8-2	No load capacity: Products not tested or submitted because they’re not load rated and code approval not required.
BPS1/2-3	No load capacity: Products not tested or submitted because they’re not load rated and code approval not required.
BPS5/8-3	No load capacity: Products not tested or submitted because they’re not load rated and code approval not required.
LBP	See specific model numbers for code listings.
LBP1/2	No load capacity: Products not tested or submitted because they’re not load rated and code approval not required.
LBP5/8	No load capacity: Products not tested or submitted because they’re not load rated and code approval not required.
LBPS1/2	Prescriptive code: Products which meet prescriptive code requirements.
LBPS5/8	Prescriptive code: Products which meet prescriptive code requirements.

Download the Simpson AutoCad Menu, which allows you to insert Ortho views directly into your AutoCAD drawing.

	ORTHOGRAPHIC	PERSPECTIVE
BP	None for this model	High Wind-Resistant Construction D43: Floor to Masonry/Concrete: DWG \| DXF High Wind-Resistant Construction D57: Pile/Girder to Wall: DWG \| DXF BP and SSTB: DWG \| DXF BP with Anchor Bolt: DWG \| DXF Sill Plate to Foundation Connections: DWG \| DXF Truss/Rafter to CMU View 1: DWG \| DXF Truss/Rafter to CMU View 2: DWG \| DXF BP: DWG \| DXF High Wind-Resistant Construction D3: Truss/Rafter to Wood Double Top Plates: DWG \| DXF High Wind-Resistant Construction D32: Truss/Rafter Hip To Single Top Plate: DWG \| DXF High Wind-Resistant Construction D33: Hollow Column Uplift: DWG \| DXF
BP1	None for this model	High Wind-Resistant Construction D57: Pile/Girder to Wall: DWG \| DXF
BP1/2	BP1/2: DWG \| DXF	None for this model
BP1/2-3	None for this model	High Wind-Resistant Construction D53: Alternative Wind Uplift Restraint System: DWG \| DXF
BP3/4	BP3/4: DWG \| DXF	None for this model
BP5/8	BP5/8: DWG \| DXF	High Wind-Resistant Construction D57: Pile/Girder to Wall: DWG \| DXF
BP5/8-2	BP5/8-2: DWG \| DXF	None for this model
BP5/8-3	None for this model	None for this model
BP7/8	None for this model	None for this model
BP7/8-2	None for this model	None for this model
BPS1/2-3	None for this model	None for this model
BPS5/8-3	None for this model	None for this model
LBP	None for this model	High Wind-Resistant Construction D3: Truss/Rafter to Wood Double Top Plates: DWG \| DXF High Wind-Resistant Construction D32: Truss/Rafter Hip To Single Top Plate: DWG \| DXF
LBP1/2	None for this model	None for this model
LBP5/8	None for this model	None for this model
LBPS1/2	None for this model	None for this model
LBPS5/8	None for this model	None for this model