Cold-Formed Steel: S/LBV, S/B and S/BA Hangers

Precision forming with manufacturing quality control provides dimensional accuracy and helps ensure proper bearing area and connection.

S/LBV, S/B, and S/BA flanges encapsulate the top flange of the joist.

Material: S/LBV, S/BA - 68 mil (14 ga); S/B - 97 mil (12 ga).

Finish: Galvanized.

Installation:

S/LBV, S/B, and S/BA

S/LBV, S/B and S/BA may be used for weld-on applications; a minimum of 1/8" x 2" fillet weld on each top flange is required. Distribute the weld equally on both top flanges. Consult the code for special considerations when welding galvanized steel. Uplift loads do not apply.

S/BA only

S/BA may be installed using powder-actuated fasteners. A 0.157" x 5/8" powder-actuated fastener shall be installed using the appropriate level of powder load so the entire pointed portion of the fastener penetrates through the steel. A powder-actuated fastener with a “tophat” crush sleeve is recommended in case the head of the fastener is not fully flush with the connector.

Options: Skew only: S/LBV and S/B series can be skewed to a maximum of 45°.

roll over images below to see larger image


S/LBV	S/B	S/BA




S/LBV, S/B and S/BA are accepable for weld-on applications (S/LBV shown)	S/LBV Installation with a CFS steel header

Tabulated loads are governed by tests and may not be increased. Refer to Steel Stress Increase for additional information.
Designer shall insure that the joist member adequately transfers load to the hanger.
Steel header must be braced to prevent buckling per Designer specification.

Tabulated loads are governed by tests and may not be increased. Refer to Steel Stress Increase for additional information.
Designer shall insure that the joist member adequately transfers load to the hanger.
Steel header by Designer.
Powder-actuated fasteners may be installed in up to 3/8" steel. Steel header shall have minimum Fy = 36,000 psi.
Loads are based on using the Simpson Strong-Tie® PDPAT-62KP powder-actuated fastener and a minimum Red (level 5) powder load.
Installations of powder-actuated fasteners may vary due to, but not limited to, the type of powder-actuated tool, cleanliness of tool, type of powder load and steel.
Allowable loads are based on testing with a minimum of 2 1/2" flange supporting member, and CFS thickness of 68 mil (14 ga) for header and joist

					Legacy Reports
	IAPMO ES ER	ICC-ES ESR	CITY OF LOS ANGELES	STATE OF FLORIDA	ICC-ES NER	ICC-ES ER	ICC-ES ES
S/B	See specific model numbers for code listings.
S/B1.56
S/B1.81
S/B2.06
S/B2.37
S/B2.56
S/B2.68
S/B3.12
S/B3.56
S/B3.62
S/B4.06
S/B4.12
S/B4.28
S/B4.75
S/B5.50	No code listing. Please contact us for test data.
S/BA	No code listing. Please contact us for test data.
S/BA2.12/10	No code listing. Please contact us for test data.
S/BA2.12/12	No code listing. Please contact us for test data.
S/BA2.12/14	No code listing. Please contact us for test data.
S/BA2.12/8	No code listing. Please contact us for test data.
S/BA4.18/10	No code listing. Please contact us for test data.
S/BA4.18/12	No code listing. Please contact us for test data.
S/BA4.18/14	No code listing. Please contact us for test data.
S/BA4.18/8	No code listing. Please contact us for test data.
S/LBV	See specific model numbers for code listings.
S/LBV1.56
S/LBV1.81
S/LBV2.06
S/LBV2.37
S/LBV2.56
S/LBV2.68
S/LBV3.12
S/LBV3.56
S/LBV3.62
S/LBV4.06
S/LBV4.12
S/LBV4.28
S/LBV4.75
S/LBV5.50	No code listing. Please contact us for test data.

Download the Simpson AutoCad Menu, which allows you to insert Ortho views directly into your AutoCAD drawing.

	ORTHOGRAPHIC	PERSPECTIVE
S/B	S/B: DWG \| DXF S/B front view: DWG \| DXF S/B right view: DWG \| DXF S/B top view: DWG \| DXF	None for this model
S/B1.56	None for this model	None for this model
S/B1.81	None for this model	None for this model
S/B2.06	None for this model	None for this model
S/B2.37	None for this model	None for this model
S/B2.56	None for this model	None for this model
S/B2.68	None for this model	None for this model
S/B3.12	None for this model	None for this model
S/B3.56	None for this model	None for this model
S/B3.62	None for this model	None for this model
S/B4.06	None for this model	None for this model
S/B4.12	None for this model	None for this model
S/B4.28	None for this model	None for this model
S/B4.75	None for this model	None for this model
S/B5.50	None for this model	None for this model
S/BA	None for this model	None for this model
S/BA2.12/10	None for this model	None for this model
S/BA2.12/12	None for this model	None for this model
S/BA2.12/14	None for this model	None for this model
S/BA2.12/8	None for this model	None for this model
S/BA4.18/10	None for this model	None for this model
S/BA4.18/12	None for this model	None for this model
S/BA4.18/14	None for this model	None for this model
S/BA4.18/8	None for this model	None for this model
S/LBV	S-LBV: DWG \| DXF S-LBV front view: DWG \| DXF S-LBV right view: DWG \| DXF S-LBV top view: DWG \| DXF	None for this model
S/LBV1.56	None for this model	None for this model
S/LBV1.81	None for this model	None for this model
S/LBV2.06	None for this model	None for this model
S/LBV2.37	None for this model	None for this model
S/LBV2.56	None for this model	None for this model
S/LBV2.68	None for this model	None for this model
S/LBV3.12	None for this model	None for this model
S/LBV3.56	None for this model	None for this model
S/LBV3.62	None for this model	None for this model
S/LBV4.06	None for this model	None for this model
S/LBV4.12	None for this model	None for this model
S/LBV4.28	None for this model	None for this model
S/LBV4.75	None for this model	None for this model
S/LBV5.50	None for this model	None for this model