Cold-Formed Steel: W/WP Hangers

USA / Canada | Change Location...

Select One of Our Sites

✖

North America

USA / Canada

Asia

中国 (China)

Oceania

Other Locations

Simpson Strong-Tie Locations

Europe

www.strongtie.com

W/WP Hangers

This series of purlin hangers offer the greatest design flexibility and versatility.

Material: Stirrup – 97 mil (12 ga)

Finish: Simpson Strong-Tie gray paint. Some models available hot-dip galvanized;
specify HDG, see Corrosion Information.

Installation: Hangers may be welded to steel headers with 1/8" for W and
3/16" for WP by 1 1/2" fillet welds located at each end of the top flange.

Options: W and H dimensions are modifiable.

SLOPED AND/OR SKEWED SEAT

W/WP series may be skewed to a maximum of 84° and/or sloped to a maximum of 45°.
For slope only, skew only, or slope and skew combinations, the allowable load is 100% of the table load.
Specify the slope up or down in degrees from the horizontal plane and/or the skew right or left in degrees from the perpendicular vertical plane. Specify whether low side, high side or center of joist will be flush with the top of the header.

top Gallery:

roll over images below to see larger image


WP		W
Some model configurations may differ from those shown. Contact Simpson Strong-Tie for details.

top Load Table: See code report listings below

For hanger heights exceeding the joist height the allowable load is 0.50 of the table value.
The Designer shall ensure that the joist member adequately transfers load to the hanger.
Not all combinations of W, H, and B dimensions are available. Contact Simpson Strong-Tie.

top Code Reports (PDFs):

					Legacy Reports
	IAPMO UES ER	ICC-ES ESR	CITY OF LOS ANGELES	STATE OF FLORIDA	ICC-ES NER	ICC-ES ER	ICC-ES ES
W	See specific model numbers for code listings.
WP	No code listing. Please contact us for test data.

topDrawings: To download drawings, right-click or Ctrl-click on the link, then choose "Save Target As..."

Download the Simpson Strong-Tie® AutoCAD® Menu, which allows you to insert Ortho views directly into your AutoCAD drawing.

	ORTHOGRAPHIC	PERSPECTIVE
W	W series: DWG \| DXF W sloped down: DWG \| DXF W sloped up: DWG \| DXF W with top flange offset left: DWG \| DXF W with top flange offset right: DWG \| DXF W series front view: DWG \| DXF W sloped down front view: DWG \| DXF W sloped up front view: DWG \| DXF W with top flange offset left front view: DWG \| DXF W with top flange offset right front view: DWG \| DXF W series left view: DWG \| DXF W sloped down left view: DWG \| DXF W sloped up left view: DWG \| DXF W with top flange offset left left view: DWG \| DXF W with top flange offset right left view: DWG \| DXF W series right view: DWG \| DXF W sloped down right view: DWG \| DXF W sloped up right view: DWG \| DXF W with top flange offset left right view: DWG \| DXF W with top flange offset right right view: DWG \| DXF W sloped down top view: DWG \| DXF W sloped up top view: DWG \| DXF W series top view: DWG \| DXF W with top flange offset left top view: DWG \| DXF W with top flange offset right top view: DWG \| DXF	LTT19 & W: DWG W Top Flange Offset: DWG \| DXF W Ridge Connection: DWG \| DXF W Skewed 1: DWG \| DXF W Top Flange Sloped 1: DWG \| DXF W Skewed 2: DWG \| DXF W Skewed Top View: DWG \| DXF W Skewed 3: DWG \| DXF W Top Flange Sloped 2: DWG \| DXF
WP	None for this model	WP Skewed: DWG \| DXF