www.strongtie.com



>>Home
New Products

PPB

PPBZ
Porch Post Base

 

PFB

PFB/PFDB
Post Frame Hangers

 

KBS1Z

KBS1Z
Knee-Brace Stabilizer

 

DHU

DU/DHU/DHUTF
Drywall Hangers

 

HTSQ

HTSQ
Twist Strap

 

RTC2Z

RTC2Z
Rigid Tie™ Connector

HTHMQ

HTHMQ
Heavy Multiple Truss Hanger

HTHGQ

HTHGQ
Truss Girder
Hanger

HHSUQ

HHSUQ
Heavy Severe-Skew Truss Hanger

HHRC

HHRC
Hip Ridge Connectors

33 Structural Collated Nails

33° Structural
Collated Nails

SDWS/SDWH

SDWS/SDWH
Structural Wood Screws

SDWC

SDWC
Structural Wood Screws

CPTZ

CPTZ
Concealed Post Tie

PPBZ Porch Post Base

The PPBZ porch post base is designed to be installed once and will support permanent porch framing throughout all stages of construction. This design eliminates the need for temporary support of the porch roof structure and provides full access to installers/inspectors. Install the PPBZ to the cured grade beam with two Simpson Strong-Tie® Titen® screws just prior to rough framing. Designed to withstand vertical construction loads prior to embedment in concrete, the PPBZ will support most framed porches and overhangs.

> more info

 

PFB/PFDB Post Frame Hangers

The PF series hangers have been redesigned to accommodate collated nails (0.148x1½) as well as the 10d common nail (0.148x3). The PFB and PFDB have dome-shaped joist nail holes that guide nails into the proper installation angle. The redesign also features a folded seat that raises the 2x joist very slightly above the seat radius to enable a tighter connection to the back of the hanger.

> more info

 

KBS1Z Knee-Brace Stabilizer

The KBS1Z knee-brace stabilizer makes a structural connection between knee bracing and columns or beams to help stabilize free-standing structures, and comply with many prescriptive deck bracing requirements such as AWC’s DCA6 Prescriptive Residential Wood Deck Construction Guide. Factory-formed at a 45˚ angle and easily installed with nails, the KBS1Z braces 2x, 4x and 6x in line post-to-beam configurations.

> more info

 

DU/DHU/DHUTF Drywall Hanger

The new DU/DHU face-mount and the DHUTF top-mount hangers are designed to carry joist floor loads to a wood stud wall through two layers of 5/8" gypsum board (drywall). These hangers install after the drywall is in place. The hangers come in sizes that accommodate most joists used in multi-family construction including I-joists and trusses.

> more info

 

HTSQ Twist Strap

The new HTSQ twist straps provide a tension connection between two wood members and are designed to resist uplift for decks, boardwalks and beams economically. The HTSQ is quicker, easier and more economical to install when compared to bolted straps. HTSQ provides a strong connection with fewer fasteners than nailed HTS straps when incorporating Simpson Strong-Tie® Strong-Drive® SDS screws.

> more info

 

RTC2Z Rigid Tie™ Connector

The new RTC2Z Rigid Tie™ corner connector connects a 2x2, 2x3 or 2x4 vertical member to two 2x3 or greater horizontal members, forming a 90° corner. This latest version requires 40% fewer fasteners (can be installed with nails or screws), than the RTC24, which saves both time and money.

> more info

 

HTHMQ Heavy Multiple Truss Hanger

This heavy-duty hanger is designed to carry 2 or 3 trusses to enable a
greater range of structural designs. Designed with versatility in mind,
the HTHMQ will accommodate various lumber types and widths and
multiple-ply trusses. The HTHMQ also facilitates right- or left-hand hips
(at 30° - 60° skews) and can be used for terminal hip trusses with or
without the center common jack.

> more info

 

HTHGQ Truss Girder Hanger

The HTHGQ is a high-capacity girder hanger designed to carry multi-ply
trusses or composite lumber. The HTHGQ can accommodate various
width for installation flexibility by enabling up to 5-ply girder trusses.
The Strong-Drive® SDS screws used help transfer the load between the
plies of the supporting girder when they penetrate all plies.

> more info

 

HHSUQ Heavy Severe-Skew Truss Hanger

The HHSUQ is a new high load capacity, face-mount, truss-to-truss
hanger designed to accommodate severe skews (45° to 84°). This
allowable skew for hip trusses enables a greater range of installation
applications. The HHSUQR model is skewed right and the HHSUQL
version is skewed left.

> more info

 

HHRC Hip Ridge Connectors

The HHRC is a 12-gauge hip ridge connector that attaches hip roof
beams to the end of a ridge beam. The HHRC is suitable for light
commercial construction and may be sloped down a maximum of
35° (12:17 hip slope).

> more info

 

33° Structural Collated Nails

The 33° collated, structural-connector nail is designed to provide installers
a pneumatically-driven alternative to hand-driven nails. This hot-dip galvanized
nail is approved for use in many Simpson Strong-Tie® connector applications.
These nails are available in 25-nail, paper-collated strips, and are compatible
with a wide variety of popular pneumatic nailers.

> more info

 

SDWS/SDWH Structural Wood Screws

Simpson Strong-Tie has expanded the Strong-Drive® SDW wood screw
product line with two new screws designed to provide an easy-to-install,
high-strength alternative to through-bolting and traditional lag screws. The
new SDWS (6-lobe drive) and SDWH (hex head) structural wood screws
are ideal for the contractor and do-it-yourselfer alike in both structural and
general-purpose applications.

> more info

 

SDWC Structural Wood Screws

The new Strong-Drive® SDW structural wood screw delivers a stud-to-bottom
plate or stud-to-top plate connection in addition to fastening rafters or trusses
to top plates. The fully-threaded shank engages the entire length of the
fastener providing a secure connection. The SDWC is tested in accordance
with ICC-ES AC233 (screw) and AC13 (wall assembly) for uplift and lateral
loads between wall plates and vertical wall framing.

> more info

 

CPTZ Concealed Post Tie

This new concealed post base incorporates a knife plate with a standoff
base. They achieve a clean, concealed look while providing a 1" standoff
height above concrete. The CPTZ is installed with 1⁄2" diameter galvanized
pins (supplied). The 1" standoff height is code-required when supporting
permanent structures that are exposed to weather or water splash, or in
basements. The standoff also reduces the potential for decay at post or
column ends.

> more info

 

Printed from
© 2014 Simpson Strong-Tie Company Inc.