www.strongtie.com


>>Home   > All Products - Alphabetical List

A Angles

Our line of angles provides a way to make a wide range of 90° connections.

Material: A21 and A23—18 ga.; all other A angles—12 ga.

Finish: Galvanized. Some products available in stainless steel or ZMAX® coating; see Corrosion Information.

Installation:

SD9 & SD10 Compatible

Some products may be installed with the Strong-Drive® SD Structural Connector screw -
click here for details


top Gallery:
  roll over images below to see larger image
 
A44 Installation
(A33 similar)
A21/A23 Installation A311 Installation
     
A24 Installation    

top Load Table: See code report listings below

Load Values with Nails

Additional Corrosion Protection

These products are available with additional corrosion protection. Additional products on this page may also be available with this option, check with Simpson Strong-Tie for details.

These models are approved for installation with the Strong-Drive SD Structural-Connector screw.
See the load values below.
Table
  1. Allowable loads have been increased for wind or earthquake loading with no further increase allowed. Reduce where other loads govern.
  2. For SPF/HF lumber use 0.86 of table loads.
  3. NAILS: 10dx1 1/2" = 0.148" dia. x 1 1/2" long, 10d = 0.148" dia. x 3" long. See other nail sizes and information.

Load Values with SD Series Screws

Additional Corrosion Protection

These products are available with additional corrosion protection. Additional products on this page may also be available with this option, check with Simpson Strong-Tie for details.

Model
No.
Fasteners DF/SP Allowable Loads SPF/HF Allowable Loads
To Rafters/ Truss To Plates/Base To Studs/Post Uplift Lateral Uplift Lateral
(160) F1 (160) F2 (160) (160) F1 (160) F2 (160)
bluearrow
A21
- 2-SD9112 2-SD9112 - 430 165 - 360 140
bluearrow
A23
- 4-SD9112 4-SD9112 - 670 560 - 580 480
A33 - 4-SD9112 4-SD9112 - 830 335 - 715 290
A44 - 4-SD9112 4-SD9112 - 805 290 - 695 250

  1. H connector loads based on installation to double top plate.
  2. Uplift load for the H4 stud to bottom plate installation is 415 lbs for DF/SP and 355 lbs for SPF/HF.
  3. Uplift load for the H8 stud to bottom plate installation is 380 lbs for DF/SP and 325 lbs for SPF/HF.

next  top Code Reports (PDFs):
Legacy Reports
  IAPMO UES ER ICC-ES ESR CITY OF LOS ANGELES STATE OF FLORIDA ICC-ES NER ICC-ES ER ICC-ES ES
ASee specific model numbers for code listings.
A21 ER-112 ESR-2523 * / ESR-3096 RR25814 / RR25910 FL10446      
A21Z ER-112 ESR-2523 * / ESR-3096 RR25814 / RR25910        
A23 ER-112 ESR-2523 * / ESR-3096 RR25814 / RR25910 FL10446      
A23Z ER-112 ESR-2523 * / ESR-3096 RR25814 / RR25910        
A24No load capacity: Products not tested or submitted because they’re not load rated and code approval not required.
A311No load capacity: Products not tested or submitted because they’re not load rated and code approval not required.
A33 ER-112 ESR-3096 RR25814 / RR25910        
A44 ER-112 ESR-3096 RR25814 / RR25910        
A66No load capacity: Products not tested or submitted because they’re not load rated and code approval not required.
A88No load capacity: Products not tested or submitted because they’re not load rated and code approval not required.



next  topDrawings: To download drawings, right-click or Ctrl-click on the link, then choose "Save Target As..."
Download the Simpson Strong-Tie® AutoCAD® Menu, which allows you to insert Ortho views directly into your AutoCAD drawing.

 ORTHOGRAPHIC
PERSPECTIVE
ANone for this model None for this model
A21None for this model A21 AND A23: DWG | DXF
A21ZNone for this model None for this model
A23 A23: DWG | DXF
A23 front view: DWG | DXF
A23 right view: DWG | DXF
A23 top view: DWG | DXF
A21 AND A23: DWG | DXF
A23 CFS: DWG | DXF
A23ZNone for this model None for this model
A24 A24: DWG | DXF
A24 front view: DWG | DXF
A24 right view: DWG | DXF
A24 top view: DWG | DXF
A24: DWG | DXF
A311 A311: DWG | DXF
A311 front view: DWG | DXF
A311 right view: DWG | DXF
A311 top view: DWG | DXF
A311: DWG | DXF
A33 A33: DWG | DXF
A33 front view: DWG | DXF
A33 right view: DWG | DXF
A33 top view: DWG | DXF
None for this model
A44 A44: DWG | DXF
A44 front view: DWG | DXF
A44 right view: DWG | DXF
A44 top view: DWG | DXF
A44: DWG | DXF
A66 A66: DWG | DXF
A66 front view: DWG | DXF
A66 right view: DWG | DXF
A66 top view: DWG | DXF
None for this model
A88 A88: DWG | DXF
A88 front view: DWG | DXF
A88 right view: DWG | DXF
A88 top view: DWG | DXF
A88: DWG | DXF

   
top
Order free catalogs by mail
top top top
Fliers (PDFs):
top
Printed from
© 2014 Simpson Strong-Tie Company Inc.