EPB Elevated Post Bases

Select One of Our Sites

North America

Asia

Oceania

Other Locations

Europe

www.strongtie.com

EPB Elevated Post Bases

Material: EPB44A—14 ga.; others—12 ga. base plate, 1 1/16" OD x 8" pipe

Finish: EPB44A—Galvanized; all others—Simpson Strong-Tie® gray paint (may be ordered HDG); see Corrosion Information.

Installation:

Use all specified fasteners. See General Notes.
Allows 1" to 2 1/2" clearance above concrete, 2" for EPB44A.
Post bases do not provide adequate resistance to prevent members from rotating about the base and therefore are not recommended for non top-supported installations (such as fences or unbraced carports).

Some products may be installed with the Strong-Drive® SD Structural Connector screw -
click here for details

Options: 12" pipe available for EPB44, 46, 66; specify “-12” after model number.

roll over images below to see larger image

These products are available with additional corrosion protection. Additional products on this page may also be available with this option, check with Simpson Strong-Tie for details.

These models are approved for installation with the Strong-Drive SD Structural-Connector screw.
See the load values.

Loads may not be increased for short-term loading.
EPB44 and EPB46 have extra nail holes; only eight must be filled to achieve table loads.
Specifier to design concrete for uplift capacity.
Downloads shall be reduced where limited by the capacity of the joist. See Post Capacities for common post allowable loads.
Structural composite lumber columns have sides that show either the wide face or the edges of the lumber strands/veneers. For SCL columns, the fasteners for these products should always be installed in the wide face.
NAILS: 16d = 0.162" dia. x 3 1/2" long. See other nail sizes and information.

					Legacy Reports
	IAPMO UES ER	ICC-ES ESR	CITY OF LOS ANGELES	STATE OF FLORIDA	ICC-ES NER	ICC-ES ER	ICC-ES ES
EPB	See specific model numbers for code listings.
EPB44	No code listing: Please contact us for test data.
EPB44-12	No code listing. Please contact us for test data.
EPB44A	No code listing: Please contact us for test data.
EPB44MB	No code listing. Please contact us for test data.
EPB44P	No code listing. Please contact us for test data.
EPB44T	No code listing: Please contact us for test data.
EPB46	No code listing: Please contact us for test data.
EPB66	No code listing: Please contact us for test data.

* ESR-2523 is an Index of many of Simpson Strong-Tie Stamped and Welded Cold-formed Steel Products for Wood or Cold-formed Steel Construction

topDrawings: To download drawings, right-click or Ctrl-click on the link, then choose "Save Target As..."

Download the Simpson Strong-Tie® AutoCAD® Menu, which allows you to insert Ortho views directly into your AutoCAD drawing.

	ORTHOGRAPHIC	PERSPECTIVE
EPB	None for this model	None for this model
EPB44	EPB44: DWG \| DXF EPB44 front view: DWG \| DXF EPB44 left view: DWG \| DXF EPB44 right view: DWG \| DXF EPB44 top view: DWG \| DXF	None for this model
EPB44-12	EPB44-12: DWG \| DXF EPB44-12 front view: DWG \| DXF EPB44-12 right view: DWG \| DXF EPB44-12 top view: DWG \| DXF	None for this model
EPB44A	EPB44A: DWG \| DXF EPB44A front view: DWG \| DXF EPB44A right view: DWG \| DXF EPB44A top view: DWG \| DXF	EPB44A: DWG \| DXF
EPB44MB	EPB44MB: DWG \| DXF EPB44MB front view: DWG \| DXF EPB44MB right view: DWG \| DXF EPB44MB top view: DWG \| DXF	None for this model
EPB44P	None for this model	None for this model
EPB44T	EPB44T: DWG \| DXF EPB44T front view: DWG \| DXF EPB44T left view: DWG \| DXF EPB44T right view: DWG \| DXF EPB44T top view: DWG \| DXF	EPB44T: DWG \| DXF EPB44T: DWG \| DXF
EPB46	EPB46: DWG \| DXF EPB46 front view: DWG \| DXF EPB46 right view: DWG \| DXF EPB46 top view: DWG \| DXF	None for this model
EPB66	EPB66: DWG \| DXF EPB66 front view: DWG \| DXF EPB66 right view: DWG \| DXF EPB66 top view: DWG \| DXF	None for this model