LCC Lally Column Caps / CCOS Steel Column Caps

Lally column caps provide adequate bearing length for larger girder reactions.

Material: 12 gauge; CCOS - 7 gauge

Finish: LCC - Simpson Strong-Tie® gray paint; CCOS - G90 Galvanized

Installation:

Use all specified fasteners. See General Notes.
LCC - Fit the lally column cap over the lally column and attach to the girder.
CCOS - Attach steel column cap to column end plate with (4) Simpson Strong-Tie Quik Drive® self-tapping screws (provided) and attach to girder.

roll over images below to see larger image


Typical LCC5.25-3.5 Installation connecting a 3-ply LVL and a 3 1/2" diameter (O.D.) steel column		Typical CCOS5.50 Installation connecting a 3-ply LVL and a steel column

Loads may not be increased for short-term loading.
Allowable loads are determined using the lowest of the bearing loads using F_c-perp equal to 425 psi for SPF, 625 psi for DF and 700 psi for LVL/PSL/LSL.
Loads are for a continuous beam.
Spliced conditions for the LCC must be detailed by the Designer to transfer tension loads between spliced members
by means other than the lally column. The splice condition load is 6750 lbs per beam side for LCC must be evenly loaded.
To achieve lateral loads, LCC pipe must be welded to the column with an 1/8" fillet weld around the entire pipe.
The CCOS must be attached to end plate of the column with (4) Quik Drive XQ112S1224 self-tapping screws through the end plate and into the bottom of the CCOS.
All pipe columns need to be designed by a qualified Designer. CCOS minimum column diameter is 3".
CCOS caps can resist out-of-plane (F₂) forces up to 2200 lbs. provided the beam is braced to resist torsional rotation.
NAILS: 16d = 0.162" dia. x 3 1/2" long, 10d = 0.148" dia. x 3" long. See other nail sizes and information.

					Legacy Reports
	IAPMO ES ER	ICC-ES ESR	CITY OF LOS ANGELES	STATE OF FLORIDA	ICC-ES NER	ICC-ES ER	ICC-ES ES
CCOS3.12	No code listing: Please contact us for test data.
CCOS3.62	No code listing: Please contact us for test data.
CCOS4.62	No code listing: Please contact us for test data.
CCOS4.62	No code listing: Please contact us for test data.
CCOS7.25	No code listing: Please contact us for test data.
LCC	See specific model numbers for code listings.
LCC3.5-3.5	No code listing: Please contact us for test data.
LCC3.5-4	No code listing: Please contact us for test data.
LCC4.5-3.5	No code listing: Please contact us for test data.
LCC4.5-4	No code listing: Please contact us for test data.
LCC5.25-3.5	No code listing: Please contact us for test data.
LCC5.25-4	No code listing: Please contact us for test data.
LCC6-3.5	No code listing: Please contact us for test data.
LCC6-4	No code listing: Please contact us for test data.
LCC7-3.5	No code listing: Please contact us for test data.
LCC7-4	No code listing: Please contact us for test data.

Download the Simpson AutoCad Menu, which allows you to insert Ortho views directly into your AutoCAD drawing.

	ORTHOGRAPHIC	PERSPECTIVE
CCOS3.12	None for this model	None for this model
CCOS3.62	None for this model	None for this model
CCOS4.62	None for this model	None for this model
CCOS7.25	None for this model	None for this model
LCC	None for this model	LCC: DWG \| DXF
LCC3.5-3.5	None for this model	None for this model
LCC3.5-4	None for this model	None for this model
LCC4.5-3.5	None for this model	None for this model
LCC4.5-4	LCC4.5-4: DWG \| DXF LCC4.5-4 front view: DWG \| DXF LCC4.5-4 left view: DWG \| DXF LCC4.5-4 right view: DWG \| DXF	None for this model
LCC5.25-3.5	None for this model	None for this model
LCC5.25-4	None for this model	None for this model
LCC6-3.5	None for this model	None for this model
LCC6-4	None for this model	None for this model
LCC7-3.5	None for this model	None for this model
LCC7-4	None for this model	None for this model