HU/HUC/HSUR/L Hangers for Masonry and Concrete

HU410 Installed on Masonry Block Sidewall

HUC410 Installed on Masonry Block End Wall

HSUR/L26-2 Installed on Masonry Block Sidewall

HU and HUC products are heavy duty face mount joist hangers made from 14 gauge galvanized steel.

The HUC is a concealed flange version of the HU. Concealed flange hangers have the face flanges turned in.
HU is available with header flanges concealed, provided the W dimension is 2 5/16" or greater, at 100% of the table load. Specify HUC.
HU is available with one header flange concealed when the W dimension is less than 2 5/16" at 100% of the table load.
For allowable loads on HU products not listed in the table see technical bulletin T-HUHUCTTN.

Material: 14 gauge

Finish: Galvanized. Some products available in stainless steel or ZMAX® coating; see Corrosion Information.

Installation:

These hangers are attached to full grouted CMU walls using 1/4" x 2 3/4" hex head Titen® screws or for concrete walls using 1/4x1 3/4" hex head Titen screws. Titen screws are not provided.
Drill the 3/16" diameter hole to the specified embedment depth plus 1/2".
Alternatively, drill the 3/16" diameter hole to the specified embedment depth and blow it clean using compressed air.
Caution: Oversized holes in the base material will reduce or eliminate the mechanical interlock of the threads with the base material and will reduce the anchor's load capacity.
The hangers should be installed such that a minimum end and edge distance of 1 1/2" is maintained.
Not recommended for exposed exterior applications.
Provide moisture barrier between beam and wall per jurisdictional requirements

roll over images below to see larger image

Uplift loads have been increased 60% for wind or earthquake duration. No further increase is allowed.
Minimum concrete strength f'_c shall be 2500 psi. CMU shall have a minimum grout strength of 2500 psi with standard ASTM C90 units and type N or S mortar.
The HU28 can be ordered skewed 45º and achieve the same loads.
See Simpson Strong-Tie Anchor Systems® website for full Titen Screw details.
Noted loads for the HSUL/R shall be 0.8 the table loads for concrete applications.
Table allowable loads were determined using tested lowest ultimate/3 or fastener calculation values.
Products shall be installed such that the Titen screws are not exposed to the weather.
NAILS: 16dx2 1/2 = 0.162" dia. x 2 1/2" long, 10d = 0.148" dia. x 3" long, 10dx1 1/2 = 0.148" dia. x 1 1/2" long. (Other nail sizes and information.)

					Legacy Reports
	IAPMO ES ER	ICC-ES ESR	CITY OF LOS ANGELES	STATE OF FLORIDA	ICC-ES NER	ICC-ES ER	ICC-ES ES
HSUL26-2		ESR-2549 / ESR-2523 *	RR25807	FL10655
HSUR	See specific model numbers for code listings.
HSUR26-2		ESR-2549 / ESR-2523 *	RR25807	FL10655
HU	See specific model numbers for code listings.
HU210		ESR-2549 / ESR-2523 *	RR25807	FL10655
HU210-2		ESR-2549 / ESR-2523 *	RR25807	FL10655
HU210-3		ESR-2549 / ESR-2523 *	RR25807	FL10655
HU212-3		ESR-2549 / ESR-2523 *	RR25807	FL10655
HU26		ESR-2549 / ESR-2523 *	RR25807	FL10655
HU26-2		ESR-2549 / ESR-2523 *	RR25807	FL10655
HU28		ESR-2549 / ESR-2523 *	RR25807	FL10655
HU28-2		ESR-2523*	RR25807	FL10655
HU410		ESR-2549 / ESR-2552 / ESR-2523 *	RR25801 / RR25807	FL10655 / FL10531
HU46		ESR-2549 / ESR-2523 *	RR25807	FL10655
HU48		ESR-2549 / ESR-2523 *	RR25807	FL10655
HUC	See specific model numbers for code listings.
HUC210-2Z		ESR-2549 / ESR-2523 *		FL10655
HUC210-3Z		ESR-2549 / ESR-2523 *		FL10655
HUC28-2Z		ESR-2549 / ESR-2523 *		FL10655
HUC410		ESR-2549 / ESR-2552 / ESR-2523 *	RR25801	FL10655 / FL10531
HUC44		ESR-2549 / ESR-2523 *		FL10655
HUC46		ESR-2549 / ESR-2523 *		FL10655
HUC48		ESR-2549 / ESR-2523 *		FL10655
HUC66		ESR-2549 / ESR-2523 *		FL10655
HUC68		ESR-2549 / ESR-2523 *		FL10655

* ESR-2523 is an Index of many of Simpson Strong-Tie Stamped and Welded Cold-formed Steel Products for Wood or Cold-formed Steel Construction

Download the Simpson AutoCad Menu, which allows you to insert Ortho views directly into your AutoCAD drawing.

	ORTHOGRAPHIC	PERSPECTIVE
HSUL26-2	None for this model	None for this model
HSUR	None for this model	None for this model
HSUR26-2	None for this model	None for this model
HU	HU sloped down skewed left: DWG \| DXF HU sloped down skewed right: DWG \| DXF HU sloped down: DWG \| DXF HU sloped left: DWG \| DXF HU skewed right: DWG \| DXF HU series: DWG \| DXF HU sloped up skewed left: DWG \| DXF HU sloped up skewed right: DWG \| DXF HU sloped up: DWG \| DXF HU sloped down skewed left front view: DWG \| DXF HU sloped down skewed right front view: DWG \| DXF HU sloped down front view: DWG \| DXF HU sloped left front view: DWG \| DXF HU skewed right front view: DWG \| DXF HU series front view: DWG \| DXF HU sloped up skewed left front view: DWG \| DXF HU sloped up skewed right front view: DWG \| DXF HU sloped up front view: DWG \| DXF HU skewed right left view: DWG \| DXF HU sloped down skewed left right view: DWG \| DXF HU series sloped down right view: DWG \| DXF HU sloped left right view: DWG \| DXF HU series right view: DWG \| DXF HU sloped up skewed left right view: DWG \| DXF HU sloped up skewed right right view: DWG \| DXF HU sloped up right view: DWG \| DXF HU sloped down top view: DWG \| DXF HU sloped left top view: DWG \| DXF HU skewed right top view: DWG \| DXF HU series top view: DWG \| DXF HU sloped up skewed left top view: DWG \| DXF HU sloped up skewed right top view: DWG \| DXF HU sloped up top view: DWG \| DXF	HU 2x Joist: DWG \| DXF HU Glulam Joist: DWG \| DXF HU 4x Joist: DWG \| DXF U&HU Skewed: DWG \| DXF
HU210	HU210: DWG \| DXF HU210 with top flange: DWG \| DXF HU210 front view: DWG \| DXF HU210 with top flange front view: DWG \| DXF HU210 left view: DWG \| DXF HU210 right view: DWG \| DXF HU210 with top flange right view: DWG \| DXF HU210 top view: DWG \| DXF HU210 with top flange top view: DWG \| DXF	None for this model
HU210-2	HU210-2: DWG \| DXF HU210-2 with top flange: DWG \| DXF HU210-2TFSKL: DWG \| DXF HU210-2TFSKR: DWG \| DXF HU210-2 front view: DWG \| DXF HU210-2 with top flange front view: DWG \| DXF HU210-2TFSKL front view: DWG \| DXF HU210-2TFSKR front view: DWG \| DXF HU210-2 left view: DWG \| DXF HU210-2 with top flange left view: DWG \| DXF HU210-2TFSKR left view: DWG \| DXF HU210-2 right view: DWG \| DXF HU210-2 with top flange right view: DWG \| DXF HU210-2TFSKL right view: DWG \| DXF HU210-2 top view: DWG \| DXF HU210-2 with top flange top view: DWG \| DXF HU210-2TFSKL top view: DWG \| DXF HU210-2TFSKR top view: DWG \| DXF	None for this model
HU210-3	HU210-3: DWG \| DXF HU210-3 front view: DWG \| DXF HU210-3 left view: DWG \| DXF HU210-3 right view: DWG \| DXF HU210-3 top view: DWG \| DXF	None for this model
HU212-3	HU212-3: DWG \| DXF HU212-3 front view: DWG \| DXF HU212-3 left view: DWG \| DXF HU212-3 right view: DWG \| DXF HU212-3 top view: DWG \| DXF	None for this model
HU26	HU26: DWG \| DXF HU26TF: DWG \| DXF HU26 front view: DWG \| DXF HU26 with top flange front view: DWG \| DXF HU26 left view: DWG \| DXF HU26 with top flange left view: DWG \| DXF HU26 right view: DWG \| DXF HU26 with top flange right view: DWG \| DXF HU26 top view: DWG \| DXF HU26 with top flange top view: DWG \| DXF	None for this model
HU26-2	HU26-2TF: DWG \| DXF HU26-2 with top flange front view: DWG \| DXF HU26-2 with top flange left view: DWG \| DXF HU26-2 with top flange right view: DWG \| DXF HU26-2 with top flange top view: DWG \| DXF	None for this model
HU28	HU28: DWG \| DXF HU28 with top flange: DWG \| DXF HU28 front view: DWG \| DXF HU28 with top flange front view: DWG \| DXF HU28 left view: DWG \| DXF HU28 with top flange left view: DWG \| DXF HU28 right view: DWG \| DXF HU28 with top flange right view: DWG \| DXF HU28 top view: DWG \| DXF HU28 with top flange top view: DWG \| DXF	None for this model
HU28-2	None for this model	None for this model
HU410	HU410: DWG \| DXF HU410TF: DWG \| DXF HU410 front view: DWG \| DXF HU410 with top flange front view: DWG \| DXF HU410 left view: DWG \| DXF HU410 with top flange left view: DWG \| DXF HU410 right view: DWG \| DXF HU410 with top flange right view: DWG \| DXF HU410 top view: DWG \| DXF HU410 with top flange top view: DWG \| DXF	None for this model
HU46	HU46: DWG \| DXF HU46 with top flange: DWG \| DXF HU46 front view: DWG \| DXF HU46 with top flange front view: DWG \| DXF HU46 left view: DWG \| DXF HU46 with top flange left view: DWG \| DXF HU46 right view: DWG \| DXF HU46 with top flange right view: DWG \| DXF HU46 top view: DWG \| DXF HU46 with top flange top view: DWG \| DXF	None for this model
HU48	HU48: DWG \| DXF HU48 with top flange: DWG \| DXF HU48 front view: DWG \| DXF HU48 with top flange front view: DWG \| DXF HU48 left view: DWG \| DXF HU48 with top flange left view: DWG \| DXF HU48 right view: DWG \| DXF HU48 with top flange right view: DWG \| DXF HU48 top view: DWG \| DXF HU48 with top flange top view: DWG \| DXF	None for this model
HUC	None for this model	HUC On a Beam: DWG \| DXF HUC On a Post: DWG \| DXF
HUC210-2Z	None for this model	None for this model
HUC210-3Z	None for this model	None for this model
HUC28-2Z	None for this model	None for this model
HUC410	HUC410: DWG \| DXF HUC410 front view: DWG \| DXF HUC410 left view: DWG \| DXF HUC410 right view: DWG \| DXF HUC410 top view: DWG \| DXF	None for this model
HUC44	HUC44: DWG \| DXF HUC44 front view: DWG \| DXF HUC44 left view: DWG \| DXF HUC44 right view: DWG \| DXF HUC44 top view: DWG \| DXF	None for this model
HUC46	HUC46: DWG \| DXF HUC46 front view: DWG \| DXF HUC46 left view: DWG \| DXF HUC46 right view: DWG \| DXF HUC46 top view: DWG \| DXF	None for this model
HUC48	HUC48: DWG \| DXF HUC48 front view: DWG \| DXF HUC48 left view: DWG \| DXF HUC48 right view: DWG \| DXF HUC48 top view: DWG \| DXF	None for this model
HUC66	HUC66: DWG \| DXF HUC66 front view: DWG \| DXF HUC66 left view: DWG \| DXF HUC66 right view: DWG \| DXF HUC66 top view: DWG \| DXF	None for this model
HUC68	HUC68: DWG \| DXF HUC68 front view: DWG \| DXF HUC68 left view: DWG \| DXF HUC68 right view: DWG \| DXF HUC68 top view: DWG \| DXF	None for this model