LSSR Slopeable/Skewable Rafter Hanger
On This Page
Face-Mount Hangers for Solid Sawn Lumber
This product's information may differ depending on the category of use. You are currently viewing details related to Face-Mount Hangers for Solid Sawn Lumber. You can also view product information related to the category: Face-Mount Hangers for Engineered Wood
Product Details
The patent-pending LSSR light slopeable/skewable rafter hanger is the next generation of a field-adjustable rafter hangers. One of its key features is that it can be installed after the rafter has been tacked into place. A versatile hanger, it is field adjustable for skews up to 45° and features an innovative hinged swivel seat which adjusts up to a 45° slope.
Key Features
- Makes it possible to install after the rafters are already in place
- Flange design allows for easy skew adjustment, from 0° to 45°
- Swivel seat adjusts easily from 0° to 45° up or down
Material
- See table
Finish
- ZMAX® coating
Installation
- Use all specified fasteners; see General Notes
- Limit on-center spacing of rafters and joists with LSSR210-2Z and LSSR410Z to 14" o.c. minimum; for the LSSR26Z, LSSR28Z and LSSR210Z, limit on-center spacing to 8" o.c. minimum
- For a common rafter:
- Slide hanger into position; adjust seat and install seat nails
- Make sure side stirrups are snug close to the joist, bend lines are plumb
- Install a face nail on each side to hold in place
- Install all round and obround holes on the header and joist
- For jack rafters:
- Fold acute side forward
- Slide hanger into position; adjust seat and install seat nails
- Make sure hanger is snug close to the joist, bend line is plumb
- Install obround nails on acute side, both header and joist
- Make sure hanger is snug close to the joist and header; bend line is plumb
- Install joist nails on obtuse side
- Bend obtuse side flange back so that header flange is flush against header
- Install header nails
Related Literature
Product Information Table
| Model No. | Joist Size (in.) | Ga. | W (in.) | H (in.) | A (in.) | Coating/Material | Packaging Qty. |
|---|---|---|---|---|---|---|---|
| LSSR1.81Z | 1 3/4 | 18 | 1 13/16 | 8 15/16 | 4 1/8 | ZMAX® | 1 |
| LSSR2.1Z | 2 to 2-1/16 | 18 | 2 1/8 | 8 15/16 | 4 1/8 | ZMAX® | 1 |
| LSSR2.37Z | 2 5/16 | 18 | 2 3/8 | 8 15/16 | 4 1/8 | ZMAX® | 1 |
| LSSR2.56Z | 2 1/2 | 18 | 2 9/16 | 8 15/16 | 4 1/8 | ZMAX® | 1 |
| LSSR210-2Z | 3 | 16 | 3 1/8 | 8 15/16 | 5 1/8 | ZMAX® | 1 |
| LSSR210Z | 1 1/2 | 18 | 1 9/16 | 9 1/8 | 2 1/2 | ZMAX® | 1 |
| LSSR26Z | 1 1/2 | 18 | 1 9/16 | 5 3/8 | 2 1/2 | ZMAX® | 1 |
| LSSR28Z | 1 1/2 | 18 | 1 9/16 | 7 1/8 | 2 1/2 | ZMAX® | 1 |
| LSSR410Z | 3 1/2 | 16 | 3 5/8 | 8 15/16 | 5 1/8 | ZMAX® | 1 |
Load Tables
These products are available with additional corrosion protection. Additional products on this page may also be available with this option, check with Simpson Strong-Tie for details.
- Uplift loads have been increased for earthquake or wind loading with no further increase allowed. Reduce where other loads govern.
- For slope-only installations, the four triangle holes may be filled for an allowable roof download of 3,015 lb. for DF/SP and 2,595 lb. for SPF/HF for LSSR 16GA.
- Roof loads are 125% of floor loads unless limited by other criteria.
- On the acute side of the skewed LSSR hanger, fill obround holes only.
- Fasteners: Nail dimensions in the table are listed diameter by length. For additional information, see Fastener Types and Sizes Specified for Simpson Strong-Tie Connectors.
Code Reports & Compliance
Drawings
| DWG | DXF | RFA | IFC | SAT | |||
|---|---|---|---|---|---|---|---|
