×

We use cookies on this site to enhance your user experience. By clicking "I AGREE" below, you are giving your consent for us to set cookies. Privacy Policy

DHU Face-Mount Fire Wall Hanger

Fire Wall Hangers for Engineered Wood

This product's information may differ depending on the category of use. You are currently viewing details related to Fire Wall Hangers for Engineered Wood. You can also view product information related to the categories of: Fire Wall Hangers for Plated Truss, Fire Wall Hangers for Solid Sawn Lumber

Engineered and tested to perform, Simpson Strong-Tie® hangers are manufactured to the highest quality standards for structural strength and safety. The DHU face-mount hanger is designed to carry joist floor loads to a wood stud wall over two layers of 5/8" gypsum board (drywall). The DHU hanger installs after the drywall is in place.

Key Features

  • DHU hangers in widths of 2 1/2" or greater may be ordered with one flange concealed.
  • Available for order skewed up to 45°.
  • Testing verifies that the DHU hangers do not reduce the two-hour fire wall assembly rating in either 2x4 or 2x6 walls.
  • DHU fire wall hangers are code listed for structural use under ICC-ES ESR-2552.
  • Hangers have been tested according to ASTM E814 and received F (flame) and T (temperature) ratings for use on one or both sides of the wall in Intertek Design No. SST/WPCF 120-01. If hangers are installed on both sides of the wall, then it must be a 2x6 wall.

Finish

  • Galvanized

Installation

  • Use all specified fasteners; see General Notes.
  • Strong-Drive® SDS Heavy-Duty Connector screws are provided with the hanger.
  • Drywall is installed first.
  • Mounted with top of hanger flush with top of wall and tight to the drywall.
  • Wall top plates must be restrained to prevent rotation. Where gravity load on top of wall is less than 150 plf, use a stud-plate tie connector at the back of each stud or provide equivalent restraint by another method as determined by designer.
  • Upper plate splices must occur at a stud location.

Options

  • May be ordered with one flange concealed for widths at least 2 1/2" wide; specify which flange when ordering. Use 74% of the table downloads and 100% of table uplift loads.
  • May be ordered skewed up to 45°. Use 75% of the table downloads and 50% of table uplift loads.

Patent Information

  • US Patent 9,394,680

Related Literature

Wood Construction Connectors 2021-2023
C-C-2021
A catalog including new product information as well as any applicable specification and installation instructions for wood-to-wood and wood-to-concrete structural connectors.
Catalog
Conectores para la construcción con madera 2021–2023
C-C-2021SP
El catálogo incluye información sobre nuevos productos, así como especificaciones e instrucciones de instalación aplicables para conectores estructurales de madera a madera y de madera a concreto.
Catalog
Wood Construction Connectors – Canadian Limit States Design
C-C-CAN2022
A complete product and application catalogue including load tables and installation information for wood-to-wood, wood-to-concrete and wood-to-masonry connectors.
Catalog
Connecteurs pour constructions en bois — Conception aux états limites canadiens
C-C-CAN2022CF
Un catalogue complet sur les produits et les applications, y compris de l’information sur l’installation et les tableaux de charge pour les connecteurs bois-à-bois, bois-à-béton et bois-à-maçonnerie.
Catalog
Face-Mount Hangers Over Two Layers of 5/8" Gypsum Board
L-C-FACEMNTFW23
This letter provides allowable loads and installation information for face-mount hangers installed over two layers of 5/8" gypsum board with Strong-Drive® SDS Heavy-Duty Connector screws.
Engineering Letter

Product Information Table

Fastener Production Information and Stuff & Things
Model No. Joist Size Ga. W (in.) H (in.) B (in.) Coating/Material Product Includes Packaging Qty.
DHU1.81/11.88 1-3/4 in. x 11-7/8 in. 12 1 13/16 11 13/16 2 1/2 Zinc Galvanized, G90 (8) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws 1
DHU1.81/14 1-3/4 in. x 14 in. 12 1 13/16 13 15/16 2 1/2 Zinc Galvanized, G90 (8) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws 1
DHU1.81/16 1-3/4 in. x 16 in. 12 1 13/16 15 15/16 2 1/2 Zinc Galvanized, G90 (8) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws 1
DHU1.81/9.5 1-3/4 in. x 9-1/2 in. 12 1 13/16 9 7/16 2 1/2 Zinc Galvanized, G90 (8) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws 1
DHU2.1/11.88 2 to 2-1/16 in. x 11-7/8 in. 12 2 1/8 11 13/16 2 1/2 Zinc Galvanized, G90 (8) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws 1
DHU2.1/14 2 to 2-1/16 in. x 14 in. 12 2 1/8 13 15/16 2 1/2 Zinc Galvanized, G90 (8) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws 1
DHU2.1/16 2 to 2-1/16 in. x 16 in. 12 2 1/8 15 15/16 2 1/2 Zinc Galvanized, G90 (8) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws 1
DHU2.1/9.5 2 to 2-1/16 in. x 9-1/2 in. 12 2 1/8 9 7/16 2 1/2 Zinc Galvanized, G90 (8) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws 1
DHU2.37/11.88 2-5/16 in. x 11-7/8 in. 12 2 3/8 11 13/16 2 1/2 Zinc Galvanized, G90 (8) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws 1
DHU2.37/14 2-5/16 in. x 14 in. 12 2 3/8 13 15/16 2 1/2 Zinc Galvanized, G90 (8) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws 1
DHU2.37/16 2-5/16 in. x 16 in. 12 2 3/8 15 15/16 2 1/2 Zinc Galvanized, G90 (8) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws 1
DHU2.37/18 2-5/16 in. x 18 in. 12 2 3/8 17 15/16 2 1/2 Zinc Galvanized, G90 (8) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws 1
DHU2.37/9.5 2-5/16 in. x 9-1/2 in. 12 2 3/8 9 7/16 2 1/2 Zinc Galvanized, G90 (8) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws 1
DHU2.56/11.88 2-1/2 in. x 11-7/8 in. 12 2 9/16 11 13/16 2 1/2 Zinc Galvanized, G90 (8) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws 1
DHU2.56/14 2-1/2 in. x 14 in. 12 2 9/16 13 15/16 2 1/2 Zinc Galvanized, G90 (8) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws 1
DHU2.56/16 2-1/2 in. x 16 in. 12 2 9/16 15 15/16 2 1/2 Zinc Galvanized, G90 (8) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws 1
DHU2.56/18 2-1/2 in. x 18 in. 12 2 9/16 17 15/16 2 1/2 Zinc Galvanized, G90 (8) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws 1
DHU2.56/20 2-1/2 in. x 20 in. 12 2 9/16 19 15/16 2 1/2 Zinc Galvanized, G90 (8) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws 1
DHU2.56/9.5 2-1/2 in. x 9-1/2 in. 12 2 9/16 9 7/16 2 1/2 Zinc Galvanized, G90 (8) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws 1
DHU210 2x10 12 1 9/16 9 1/8 2 1/2 Zinc Galvanized, G90 (8) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws 1
DHU212 2x12 12 1 9/16 11 1/8 2 1/2 Zinc Galvanized, G90 (8) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws 1
DHU3.56/11.88 3-1/2 in. x 11-7/8 in. 12 3 9/16 11 13/16 2 1/2 Zinc Galvanized, G90 (8) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws 1
DHU3.56/14 3-1/2 in. x 14 in. 12 3 9/16 13 15/16 2 1/2 Zinc Galvanized, G90 (8) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws 1
DHU3.56/16 3-1/2 in. x 16 in. 12 3 9/16 15 15/16 2 1/2 Zinc Galvanized, G90 (8) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws 1
DHU3.56/18 3-1/2 in. x 18 in. 12 3 9/16 17 15/16 2 1/2 Zinc Galvanized, G90 (8) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws 1
DHU3.56/20 3-1/2 in. x 20 in. 12 3 9/16 19 15/16 2 1/2 Zinc Galvanized, G90 (8) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws 1
DHU3.56/22 3-1/2 in. x 22 in. 12 3 9/16 21 15/16 2 1/2 Zinc Galvanized, G90 (8) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws 1
DHU3.56/24 3-1/2 in. x 24 in. 12 3 9/16 23 15/16 2 1/2 Zinc Galvanized, G90 (8) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws 1
DHU3.56/9.5 3-1/2 in. x 9-1/2 in. 12 3 9/16 9 7/16 2 1/2 Zinc Galvanized, G90 (8) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws 1

Product Information Tables

Load Tables

DHU Load Table
  1. Loads assume 5/8" Type X drywall attached per IBC. Wall assembly must consist at a minimum of two 2x4 plate members with studs spaced not more than 16" o.c. For alternative solutions to mounting over a single layer of drywall, refer to the technical bulletin T-C-TFWALL.
  2. Hangers spaced closer than 16" o.c. shall reduce allowable load proportionately.
  3. Triangular nail holes may be filled with (4) additional 0.148" x 1 1/2" to achieve an allowable upliftl load of 750 lb.
  4. DF carried members with a minimum of 1 1/2" x 2 1/2" solid sawn chord dimensions may increase Allowable Uplift Load to 170 lb.
  5. Allowable downloads may be increased to 1,885 lb. for DF/SP and 1,585 lb. for SPF/HF using the DHU3.56 /24 model.
  6. For a DHU two-sided (back-to-back) application on a 2x6 wall, use 1,200 lb. allowable download for DF/SP plates and use 1,005 lb. for SPF/HF plates.
  7. For installations of two layers of gypsum wall board over 5/8" maximum wood structural panel, the DHU has an allowable download of 1,975 lb. for DF/SP plates and 1,660 lb. for SPF/HF plates.

Fastener Table

DHU Fastener Table

Code Reports & Compliance

Drawings

PDF DWG DXF RFA IFC SAT

Related Products

DHUTF
DHUTF
Top-Flange Fire Wall Hanger
DU
DU
Face-Mount Fire Wall Hanger