We use cookies on this site to enhance your user experience. By clicking "I AGREE" below, you are giving your consent for us to set cookies. Privacy Policy

text.skipToContent text.skipToNavigation

Zinc Nailon™ Pin Drive Anchor

Zinc Nailon™

On This Page

Zinc Nailon anchors are low-cost, easy-to-install anchors for applications under static loads.

Key Features

  • Available with carbon and stainless-steel pins
  • Pin and head configuration designed to make anchor tamper-resistant

Material

  • Body — Die-cast Zamac 3 alloy
  • Pin — Carbon steel; Type 304 stainless steel

Installation

  1. Drill a hole in base material using a carbide drill bit the same diameter as the nominal diameter of the anchor to be installed. Drill the hole to specified embedment depth, plus 1/4" for pin extension, and blow hole clean using compressed air. Alternatively, drill the hole deep enough to accommodate embedment depth and dust from drilling.
  2. Position fixture and insert Nailon anchor.
  3. Tap with hammer until flush with fixture, then drive pin until flush with top of head.

Caution

  • Not for use in overhead applications
  • Nailon anchors are not recommended for eccentric tension (prying) loads — capacity will be greatly reduced in such applications

Related Literature

2019–2021 Product Guide — Anchoring, Fastening Systems and Restoration Solutions for Concrete and Masonry
S-A-PG19
A product guide for Simpson Strong-Tie® providing information on adhesives, mechanical anchors, direct fastening, carbide drill bits, and concrete restoration products, for concrete and masonry.
Product Guide
Anchoring, Fastening, Restoration and Strengthening Systems for Concrete and Masonry
C-A-2021
An informative and comprehensive catalog of products belonging to our anchoring, fastening, restoration and strengthening systems for concrete and masonry.
Catalog
Sistemas de anclaje, sujeción, restauración y fortalecimiento para concreto y mampostería
C-A-2021SP
Un catálogo completo de productos e información para los sistemas de anclaje, sujeción, restauración y fortalecimiento para concreto y mampostería.
Catalog
2019–2021 Guía de productos - Anclaje, sistemas de sujeción y soluciones de restauración para concreto y mampostería
S-A-PG19SP
Guía de productos para Simpson Strong-Tie® con información sobre anclajes adhesivos, anclajes mecánicos, sujeción directa, brocas de carburo y productos para restauración para concreto y mampostería.
Product Guide
Tension Performance of Post-Installed Anchors Adjacent to Abandoned Holes
L-A-ABANHOLE21
This letter is intended to address the performance of Simpson Strong-Tie® post-installed concrete anchors in normal-weight concrete when installed adjacent to holes that have been abandoned.
Engineering Letter
Safety Data Sheet for Mechanical Anchors
SDS-MechAnchors-NA-ENG-0520
Intended to provide information for use in workplace chemical management; information such as physical properties; hazards; protective measures; precautions for handling, storing, and transportation.
SDS
Ficha de Datos de Seguridad para Anclas Mecánicas
SDS-MechAnchors-NA-ES
Diseñado para dar información útil en la gestión de químicos en el lugar de trabajo; p.ej. propiedades físicas; riesgos; medidas de protección; precauciones para manejo, almacenamiento y transporte.
SDS
Fiche de Données de Sécurité pour Ancrages Mécaniques
SDS-MechAnchors-NA-FRCA
Prévu pour fournir de l’information sur la gestion des produits chimiques au travail comme propriétés physiques, dangers, mesures de protection et précautions de manipulation, stockage et transport.
SDS

Product Information Table

Fastener Production Information and Stuff & Things
Model No. Head Type Coating/Material Size (in.) Drill Bit Dia. (in.) Component Material, Anchor Body Component Material, Pin Box Qty. Carton Qty.
ZN25034SS Mushroom Head Type 304 Stainless Steel 1/4 x 3/4 1/4 Die-cast Zamac 3 alloy Type 304 Stainless Steel 100 500
ZN25100SS Mushroom Head Type 304 Stainless Steel 1/4 x 1 1/4 Die-cast Zamac 3 alloy Type 304 Stainless Steel 100 500
ZN25112SS Mushroom Head Type 304 Stainless Steel 1/4 x 1 1/2 1/4 Die-cast Zamac 3 alloy Type 304 Stainless Steel 100 500
ZN25114SS Mushroom Head Type 304 Stainless Steel 1/4 x 1 1/4 1/4 Die-cast Zamac 3 alloy Type 304 Stainless Steel 100 500
ZN25200SS Mushroom Head Type 304 Stainless Steel 1/4 x 2 1/4 Die-cast Zamac 3 alloy Type 304 Stainless Steel 100 400
ZN25212SS Mushroom Head Type 304 Stainless Steel 1/4 x 2 1/2 1/4 Die-cast Zamac 3 alloy Type 304 Stainless Steel 100 400
ZN25300SS Mushroom Head Type 304 Stainless Steel 1/4 x 3 1/4 Die-cast Zamac 3 alloy Type 304 Stainless Steel 100 400
ZN18078 Mushroom Head Carbon Steel 3/16 x 7/8 3/16 Die-cast Zamac 3 alloy Carbon Steel 100 500
ZN25034 Mushroom Head Carbon Steel 1/4 x 3/4 1/4 Die-cast Zamac 3 alloy Carbon Steel 100 500
ZN25100 Mushroom Head Carbon Steel 1/4 x 1 1/4 Die-cast Zamac 3 alloy Carbon Steel 100 500
ZN25112 Mushroom Head Carbon Steel 1/4 x 1 1/2 1/4 Die-cast Zamac 3 alloy Carbon Steel 100 500
ZN25114 Mushroom Head Carbon Steel 1/4 x 1 1/4 1/4 Die-cast Zamac 3 alloy Carbon Steel 100 500
ZN25200 Mushroom Head Carbon Steel 1/4 x 2 1/4 Die-cast Zamac 3 alloy Carbon Steel 100 400
ZN25212 Mushroom Head Carbon Steel 1/4 x 2 1/2 1/4 Die-cast Zamac 3 alloy Carbon Steel 100 400
ZN25300 Mushroom Head Carbon Steel 1/4 x 3 1/4 Die-cast Zamac 3 alloy Carbon Steel 100 400

Product Information Tables

Zinc Nailon™ Product Data
Size (in.) Carbon Steel Pin Model No. Stainless Steel Pin Model No. Quantity
Box Carton Bulk
3/16 x 7/8 ZN18078 — 100 1,600 3,000
1/4 x 3/4 ZN25034 ZN25034SS 100 500 2,000
1/4 x 1 ZN25100 ZN25100SS 100 500 1,500
1/4 x 1 1/4 ZN25114 ZN25114SS 100 500 1,500
1/4 x 1 1/2 ZN25112 ZN25112SS 100 500 1,000
1/4 x 2 ZN25200 ZN25200SS 100 400 1,000
1/4 x 2 1/2 ZN25212 ZN25212SS 100 400 1,000
1/4 x 3 ZN25300 ZN25300SS 100 400 1,000
Allowable Tension and Shear Loads for Zinc Nailon™ in Normal-Weight Concrete
Size (in.) Drill Bit Dia. (in.) Embed. Depth (in.) Ultimate Loads (lb.) Allowable Loads (lb.)1
f'c ≥ 3,000 psi f'c ≥ 3,000 psi
Tension Shear Tension Shear
3/16 3/16 5/8 460 465 115 115
1/4 1/4 5/8 590 635 150 160
3/4 780 765 195 190
1 1/2 1,050 1,050 265 265
  1. The allowable loads are based on a safety factor of 4.0.

Code Reports & Compliance

Drawings

PDF DWG DXF RFA IFC SAT