We use cookies on this site to enhance your user experience. By clicking "I AGREE" below, you are giving your consent for us to set cookies. Privacy Policy

text.skipToContent text.skipToNavigation

Sleeve-All® Sleeve Anchor

Sleeve-All®

On This Page

Sleeve-All expanding anchors are pre-assembled, expanding sleeve anchors for use in all types of solid base materials. This anchor is available in acorn, hex, rod coupler or flat head style for a wide range of applications.

Material

  • Carbon steel or stainless steel

Finish

  • Carbon steel anchors are zinc plated

Installation

  1. Drill a hole in the base material using a carbide drill bit the same diameter as the nominal diameter of the anchor to be installed.
  2. Drill the hole to the specified embedment depth, and blow it clean using compressed air. (Overhead installations need not be blown clean.) Alternatively, drill the hole deep enough to accommodate embedment depth and the dust from drilling.
  3. Place the anchor in the fixture, and drive it into the hole until the washer and nut are tight against the fixture.
  4. Tighten to required installation torque.

 

Sleeve-All Diameter (in.) Drill Bit Size (in.) Wrench Size (in.)1 Phillips Drive Size2 Wrench Size for Coupler Nut (in.) Concrete Installation Torque (ft.-lbf.)
1/4 1/4 3/8 #3 – 5
5/16 5/16 7/16 #3 – 8
3/8 3/8 1/2 #4 1/2 15
1/2 1/2 9/16 – 5/8 25
5/8 5/8 3/4 – 3/4 50
3/4 3/4 15/16 – – 90
  1. Applies to acorn- and hex-head configurations only.
  2. Applies to flat-head configuration only.

Caution

  • Oversized holes will make it difficult to set the anchor and will reduce the anchor's load capacity

Related Literature

2019–2021 Product Guide — Anchoring, Fastening Systems and Restoration Solutions for Concrete and Masonry
S-A-PG19
A product guide for Simpson Strong-Tie® providing information on adhesives, mechanical anchors, direct fastening, carbide drill bits, and concrete restoration products, for concrete and masonry.
Product Guide
Anchoring, Fastening, Restoration and Strengthening Systems for Concrete and Masonry
C-A-2021
An informative and comprehensive catalog of products belonging to our anchoring, fastening, restoration and strengthening systems for concrete and masonry.
Catalog
Sistemas de anclaje, sujeción, restauración y fortalecimiento para concreto y mampostería
C-A-2021SP
Un catálogo completo de productos e información para los sistemas de anclaje, sujeción, restauración y fortalecimiento para concreto y mampostería.
Catalog
2019–2021 Guía de productos - Anclaje, sistemas de sujeción y soluciones de restauración para concreto y mampostería
S-A-PG19SP
Guía de productos para Simpson Strong-Tie® con información sobre anclajes adhesivos, anclajes mecánicos, sujeción directa, brocas de carburo y productos para restauración para concreto y mampostería.
Product Guide
Tension Performance of Post-Installed Anchors Adjacent to Abandoned Holes
L-A-ABANHOLE21
This letter is intended to address the performance of Simpson Strong-Tie® post-installed concrete anchors in normal-weight concrete when installed adjacent to holes that have been abandoned.
Engineering Letter
Safety Data Sheet for Mechanical Anchors
SDS-MechAnchors-NA-ENG-0520
Intended to provide information for use in workplace chemical management; information such as physical properties; hazards; protective measures; precautions for handling, storing, and transportation.
SDS
Ficha de Datos de Seguridad para Anclas Mecánicas
SDS-MechAnchors-NA-ES
Diseñado para dar información útil en la gestión de químicos en el lugar de trabajo; p.ej. propiedades físicas; riesgos; medidas de protección; precauciones para manejo, almacenamiento y transporte.
SDS
Fiche de Données de Sécurité pour Ancrages Mécaniques
SDS-MechAnchors-NA-FRCA
Prévu pour fournir de l’information sur la gestion des produits chimiques au travail comme propriétés physiques, dangers, mesures de protection et précautions de manipulation, stockage et transport.
SDS
MasterFormat® Specification for Anchor Products
T-A-MSTRANCH21
Specification data for Simpson Strong-Tie Anchor products.
MasterFormat® Specification
MasterFormat® Specification for Anchor Products
T-A-MSTRANCH21
Specification data for Simpson Strong-Tie Anchor products.
MasterFormat® Specification

Product Information Table

Fastener Production Information and Stuff & Things
Model No. Head Type Coating/Material Size (in.) Bolt Dia. (in.) Drill Bit Dia. (in.) Wrench Size (in.) TPI Max. Fixture Thickness (in.) Box Qty. Carton Qty.
SL25138A Acorn Head Zinc Plated / Carbon Steel 1/4 x 1 3/8 3/16 1/4 3/8 24 1/4 100 500
SL25214A Acorn Head Zinc Plated / Carbon Steel 1/4 x 2 1/4 3/16 1/4 3/8 24 1 1/8 100 500
SL37178C Rod-Coupler Head Zinc Plated / Carbon Steel 3/8 x 1 7/8 For 3/8" rod 3/8 1/2 18 - 50 200
SL50214C Rod-Coupler Head Zinc Plated / Carbon Steel 1/2 x 2 1/4 For 1/2" rod 1/2 5/8 16 - 25 100
SL62214C Rod-Coupler Head Zinc Plated / Carbon Steel 5/8 x 2 1/4 For 5/8" rod 5/8 3/4 13 - 20 80
SL37178HSS Hex Head Type 304 Stainless Steel 3/8 x 1 7/8 5/16 3/8 1/2 18 3/8 50 250
SL37300HSS Hex Head Type 304 Stainless Steel 3/8 x 3 5/16 3/8 1/2 18 1 1/2 50 200
SL50300HSS Hex Head Type 304 Stainless Steel 1/2 x 3 3/8 1/2 9/16 16 3/4 25 100
SL50400HSS Hex Head Type 304 Stainless Steel 1/2 x 4 3/8 1/2 9/16 16 1 3/4 25 100
SL31112H Hex Head Zinc Plated / Carbon Steel 5/16 x 1 1/2 1/4 5/16 7/16 20 3/8 100 500
SL31212H Hex Head Zinc Plated / Carbon Steel 5/16 x 2 1/2 1/4 5/16 7/16 20 1 1/16 50 250
SL37178H Hex Head Zinc Plated / Carbon Steel 3/8 x 1 7/8 5/16 3/8 1/2 18 3/8 50 250
SL37300H Hex Head Zinc Plated / Carbon Steel 3/8 x 3 5/16 3/8 1/2 18 1 1/2 50 200
SL37400H Hex Head Zinc Plated / Carbon Steel 3/8 x 4 5/16 3/8 1/2 18 2 1/4 50 200
SL50214H Hex Head Zinc Plated / Carbon Steel 1/2 x 2 1/4 3/8 1/2 9/16 16 1/2 50 200
SL50300H Hex Head Zinc Plated / Carbon Steel 1/2 x 3 3/8 1/2 9/16 16 3/4 25 100
SL50400H Hex Head Zinc Plated / Carbon Steel 1/2 x 4 3/8 1/2 9/16 16 1 3/4 25 100
SL50600H Hex Head Zinc Plated / Carbon Steel 1/2 x 6 3/8 1/2 9/16 16 3 3/8 20 80
SL62214H Hex Head Zinc Plated / Carbon Steel 5/8 x 2 1/4 1/2 5/8 3/4 13 1/2 25 100
SL62300H Hex Head Zinc Plated / Carbon Steel 5/8 x 3 1/2 5/8 3/4 13 3/4 20 80
SL62414H Hex Head Zinc Plated / Carbon Steel 5/8 x 4 1/4 1/2 5/8 3/4 13 1 1/2 10 40
SL62600H Hex Head Zinc Plated / Carbon Steel 5/8 x 6 1/2 5/8 3/4 13 3 1/4 10 40
SL75212H Hex Head Zinc Plated / Carbon Steel 3/4 x 2 1/2 5/8 3/4 15/16 11 1/2 10 40
SL75414H Hex Head Zinc Plated / Carbon Steel 3/4 x 4 1/4 5/8 3/4 15/16 11 7/8 10 40
SL75614H Hex Head Zinc Plated / Carbon Steel 3/4 x 6 1/4 5/8 3/4 15/16 11 2 7/8 5 20
SL25200PF Phillips Flat Head Zinc Plated / Carbon Steel 1/4 x 2 3/16 1/4 - 24 7/8 100 500
SL25300PF Phillips Flat Head Zinc Plated / Carbon Steel 1/4 x 3 3/16 1/4 - 24 1 7/8 50 250
SL31212PF Phillips Flat Head Zinc Plated / Carbon Steel 5/16 x 2 1/2 1/4 5/16 - 20 1 1/16 50 250
SL31312PF Phillips Flat Head Zinc Plated / Carbon Steel 5/16 x 3 1/2 1/4 5/16 - 20 2 1/16 50 250
SL37234PF Phillips Flat Head Zinc Plated / Carbon Steel 3/8 x 2 3/4 5/16 3/8 - 18 1 1/4 50 200
SL37400PF Phillips Flat Head Zinc Plated / Carbon Steel 3/8 x 4 5/16 3/8 - 18 2 1/2 50 200
SL37500PF Phillips Flat Head Zinc Plated / Carbon Steel 3/8 x 5 5/16 3/8 - 18 3 1/2 50 200
SL37600PF Phillips Flat Head Zinc Plated / Carbon Steel 3/8 x 6 5/16 3/8 - 18 4 1/2 50 200

Product Information Tables

Sleeve-All® Anchor Product Data — Zinc-Plated Carbon Steel
Size (in.) Model No. Head Style Bolt Diameter – Threads per inch Max. Fixture Thickness (in.) Quantity
Box Carton
1/4 x 1 3/8 SL25138A Acorn Head 3/16–24 1/4 100 500
1/4 x 2 1/4 SL25214A 1 1/8 100 500
5/16 x 1 1/2* SL31112H Hex Head 1/4–20 3/8 100 500
5/16 x 2 1/2 SL31212H 1 1/16 50 250
3/8 x 1 7/8 SL37178H 5/16–18 3/8 50 250
3/8 x 3 SL37300H 1 1/2 50 200
3/8 x 4 SL37400H 2 1/4 50 200
1/2 x 2 1/4* SL50214H 3/8–16 1/2 50 200
1/2 x 3 SL50300H 3/4 25 100
1/2 x 4 SL50400H 1 3/4 25 100
1/2 x 6 SL50600H 3 3/8 20 80
5/8 x 2 1/4* SL62214H 1/2–13 1/2 25 100
5/8 x 3 SL62300H 3/4 20 80
5/8 x 4 1/4 SL62414H 1 1/2 10 40
5/8 x 6 SL62600H 3 1/4 10 40
3/4 x 2 1/2* SL75212H 5/8–11 1/2 10 40
3/4 x 4 1/4 SL75414H 7/8 10 40
3/4 x 6 1/4 SL75614H 2 7/8 5 20
1/4 x 2 SL25200PF Phillips Flat Head 3/16–24 7/8 100 500
1/4 x 3 SL25300PF 1 7/8 50 250
5/16 x 2 1/2 SL31212PF 1/4–20 1 1/16 50 250
5/16 x 3 1/2 SL31312PF 2 1/16 50 250
3/8 x 2 3/4 SL37234PF 5/16–18 1 1/4 50 200
3/8 x 4 SL37400PF 2 1/2 50 200
3/8 x 5 SL37500PF 3 1/2 50 200
3/8 x 6 SL37600PF 4 1/2 50 200
1/4 x 2 3/4 SL25234 R Round Head 3/16–24 7/8 50 250
*These models do not meet minimum embedment requirements for rated load values.
Sleeve-All® Anchor Product Data – Stainless Steel
Size (in.) Model No. Head Style Bolt Diameter – Threads per inch Max. Fixture Thickness (in.) Quantity
Box Carton
3/8 x 1 7/8 SL37178HSS Hex Head 5/16–18 3/8 50 250
3/8 x 3 SL37300HSS 1 1/2 50 200
1/2 x 3 SL50300HSS 3/8–16 3/4 25 100
1/2 x 4 SL50400HSS 1 3/4 25 100
Sleeve-All® Anchor (with rod coupler) Product Data – Zinc-Plated Carbon Steel
Size (in.) Model No. Accepts Rod Dia. (in.) Wrench Size Quantity
Box Carton
3/8 x 1 7/8 SL37178C 3/8 1/2 50 200
1/2 x 2 1/4 SL50214C 1/2 5/8 25 100
5/8 x 2 1/4 SL62214C 5/8 3/4 20 80
Material Specifications
Anchor Component Zinc-Plated Carbon Steel 304 Stainless Steel
Anchor Body Material meets minimum 50,000 psi tensile Type 304
Sleeve SAE J403, Grade 1008 Cold-Rolled Steel Type 304
Nut Commercial Grade, meets requirements of ASTM A563 Grade A Type 304
Washer SAE J403, Grade 1008 /1010 Cold-Rolled Steel Type 304
Sleeve-All® Anchor Installation Data
Sleeve-All Dia. (in.) 1/4 5/16 3/8 1/2 5/8 3/4
Drill Bit Size (in.) 1/4 5/16 3/8 1/2 5/8 3/4
Wrench Size1 (in.) 3/8 7/16 1/2 9/16 3/4 15/16
Wrench Size for Coupler Nut (in.) 1/2 5/8 3/4 –
  1. Applies to acorn- and hex-head configurations only.
Length Identification Head Marks on Sleeve-All Anchors (corresponds to length of anchor – inches)
Mark A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
From 1 1/2 2 2 1/2 3 3 1/2 4 4 1/2 5 5 1/2 6 6 1/2 7 7 1/2 8 8 1/2 9 9 1/2 10 11 12 13 14 15 16 17 18
Up To But Not Including 2 2 1/2 3 3 1/2 4 4 1/2 5 5 1/2 6 6 1/2 7 7 1/2 8 8 1/2 9 9 1/2 10 11 12 13 14 15 16 17 18 19

Code Reports & Compliance

Drawings

PDF DWG DXF RFA IFC SAT