We use cookies on this site to enhance your user experience. By clicking "I AGREE" below, you are giving your consent for us to set cookies. Privacy Policy

text.skipToContent text.skipToNavigation

Titen HD® Heavy-Duty Screw Anchor

Titen HD®

On This Page

A high-strength screw anchor for use in cracked and uncracked concrete, as well as uncracked masonry. The Titen HD offers low installation torque and outstanding performance. Designed for use in dry, interior, non-corrosive environments or temporary outdoor applications.

The stainless-steel Titen HD is the optimal choice for applications in corrosive or extreme environments such as salt water, or when chemical or corrosive solutions are present. See Stainless-Steel Titen HD for more information.

Key Features

  • Tested in accordance with ACI 355.2, AC193 and AC106
  • Qualified for static and seismic loading conditions
  • Thread design undercuts to efficiently transfer the load to the base material
  • Standard fractional sizes
  • Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
  • No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
  • Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
  • Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
  • Reuse of the anchor will not achieve listed loads and is not recommended

Material

  • Carbon steel

Finish

  • Zinc plated or mechanically galvanized
  • Not recommended for permanent exterior use or highly corrosive environments

Installation

  1. Drill a hole in the base material using a carbide drill bit the same diameter as the nominal diameter of the anchor to be installed. Drill the hole to the specified embedment depth plus minimum hole depth overdrill (see table below) to allow the thread tapping dust to settle, and blow it clean using compressed air. (Overhead installations need not be blown clean.) Alternatively, drill the hole deep enough to accommodate embedment depth and the dust from drilling and tapping.
  2. Insert the anchor through the fixture and into the hole.
  3. Tighten the anchor into the base material until the hex-washer head contacts the fixture.
Titen HD Diameter (in.) Wrench Size (in.) Recommended Fixture Hole Size (in.) Min. Hole Depth Overdrill (in.)
Suggested fixture hole sizes are for structural steel thicker than 12 gauge only. Larger holes are not required for wood or thinner cold-formed steel members.
1/4 3/8 3/8 to 7/16 1/8
3/8 9/16 1/2 to 9/16 1/4
1/2 3/4 5/8 to 11/16 1/2
5/8 15/16 3/4 to 13/16 1/2
3/4 1 1/8 7/8 to 15/16 1/2

Caution

  • Holes in metal fixtures to be mounted should match the diameter specified in the table below.
  • Use a Titen HD screw anchor one time only — installing the anchor multiple times may result in excessive thread wear and reduce load capacity.
  • Do not use impact wrenches to install into hollow CMU.
  • Oversized holes in base material will reduce or eliminate the mechanical interlock of the threads with the base material and reduce the anchor’s load capacity.

Related Literature

2019–2021 Product Guide — Anchoring, Fastening Systems and Restoration Solutions for Concrete and Masonry
S-A-PG19
A product guide for Simpson Strong-Tie® providing information on adhesives, mechanical anchors, direct fastening, carbide drill bits, and concrete restoration products, for concrete and masonry.
Product Guide
Anchoring, Fastening, Restoration and Strengthening Systems for Concrete and Masonry
C-A-2021
An informative and comprehensive catalog of products belonging to our anchoring, fastening, restoration and strengthening systems for concrete and masonry.
Catalog
Sistemas de anclaje, sujeción, restauración y fortalecimiento para concreto y mampostería
C-A-2021SP
Un catálogo completo de productos e información para los sistemas de anclaje, sujeción, restauración y fortalecimiento para concreto y mampostería.
Catalog
Connectors and Fasteners for Mass Timber Construction Catalog
C-C-MASSTIMBER20
A catalog featuring connectors and fasteners for mass timber and CLT construction solutions.
Catalog
2019–2021 Guía de productos - Anclaje, sistemas de sujeción y soluciones de restauración para concreto y mampostería
S-A-PG19SP
Guía de productos para Simpson Strong-Tie® con información sobre anclajes adhesivos, anclajes mecánicos, sujeción directa, brocas de carburo y productos para restauración para concreto y mampostería.
Product Guide
Deck Connection and Fastening Guide
F-DECKCODE22
A guide to deck building and for retrofitting safer, longer-lasting outdoor decks, with 2018 and 2021 IRC/IBC code-compliant solutions for using the latest anchors, connectors and fasteners.
Product Guide
High Wind Guide
F-C-HWG20
A comprehensive guide to help Designers select the most appropriate connections for challenging, high-wind regions.
Product Guide
Installer's Pocket Guide
S-C-INSTALL19
A bilingual pocket installation guide for connectors.
Product Guide
RCA-C Rigid Connector Angle for Concrete
F-CF-RCAC22
A flier illustrating the RCA-C rigid connector angle for use in attaching stud framing to concrete supports.
Flier
Titen Screw Anchors
S-A-TITENFAM21
A sales flier detailing the breadth of the Titen® screw anchor product line.
Flier
High-Wind Retrofit Solutions for Homeowners
S-C-HWRGUIDE22
A flier providing recommendations on reducing the risk of hurricane- and other wind-induced damage to existing homes.
Flier
Retrofit Solutions for Hawaii Homeowners
S-C-22TWHRG21
A flier providing recommendations on reducing the risk of seismic, hurricane and high-wind induced damage to existing homes in Hawaii.
Flier
Soft-Story Retrofit Solutions for Northern California
F-L-20NCSSR20
A flier offering a variety of Simpson Strong-Tie® state-of-the-art structural retrofit solutions specifically designed to meet recent Northern California soft-story retrofit mandates.
Flier
ICF Connectors
F-C-ICFVL19
A flier featuring installation instructions for the ICFVL ledger connector system and provides information on the various products we have to serve the ICF market.
Flier
Seismic Retrofit Guide for Raised Foundations
F-SEISRETRGD19
A seismic retrofit guide for homes with raised foundations. This guide helps homeowners understand how to inspect, evaluate and perform basic retrofit construction using Simpson Strong-Tie products.
Flier
ICF Connectors
F-C-ICFVLCAN19
A flier providing product and installation information about the various Simpson Strong-Tie products available to serve the ICF Ledger Connector Systems in Canada.
Flier
Titen HD® Design Information — Concrete
TEB-A-THD22
This technical engineering bulletin provides a supplement to the Anchoring, Fastening and Restoration Systems for Concrete and Masonry catalog.
Technical Bulletin
ASCE 41 Values
TEB-ASCE4122
Connector and anchor Strength Design capacities for retrofits designed in accordance with ASCE 41.
Technical Bulletin
Canadian Addendum for 2021 Anchor Catalogue
TEBC-A-2021
This technical engineering bulletin for Canada, TEBC-A-2021, provides a supplement to the Anchoring, Fastening and Restoration Systems for Concrete and Masonry catalog, C-A-2021.
Technical Bulletin
Code-Compliant Sill Plate Anchorage Solutions
T-A-SILPLANCH21
A technical bulletin providing an overview of code-compliant sill plate anchorage solutions.
Technical Bulletin
Proof Load Guidelines for Titen HD® Anchors
T-A-THDINSP21
A technical bulletin providing information on proof load guidelines for Titen HD® anchors.
Technical Bulletin
Soluciones de anclajes de soleras que cumplen con el código
T-A-SILPANC21SP
Un boletín técnico que brinda un resumen sobre las soluciones de anclajes de soleras que cumplen con el código.
Technical Bulletin
Connector Solutions to Meet the Wall Bracing Requirements of the International Residential Code®
T-C-WALLBRACE21
A technical bulletin providing technical information about wall bracing methods and code sections that require connectors (e.g., holdowns or straps) and anchors.
Technical Bulletin
Hollow Column Uplift Connections
T-C-COLUMN22
A technical bulletin providing information on achieving uplift loads for hollow columns with a concealed connection using a combination of Simpson Strong-Tie anchors and threaded rods or coil straps.
Technical Bulletin
Simpson Strong-Tie® Titen HD® Screw Anchor for the CONNECT-EZ™ PA-12 Panel Anchor
L-A-THDEZPA1222
Simpson Strong-Tie supports the use of the Titen HD screw anchor model no. THD75100H with the CONNECT-EZ panel anchor (PA-12) when conforming to the details shown in this letter.
Engineering Letter
Tension Performance of Post-Installed Anchors Adjacent to Abandoned Holes
L-A-ABANHOLE21
This letter is intended to address the performance of Simpson Strong-Tie® post-installed concrete anchors in normal-weight concrete when installed adjacent to holes that have been abandoned.
Engineering Letter
Titen HD® Installed into Hollow-Core Concrete Slabs
L-A-THDHCP21
This letter provides tested capacities of our Titen HD anchors into hollow-core concrete panels.
Engineering Letter
Substitution of PDPA/PDPAWL-287 PAF with Titen Turbo™ and Titen HD® Screw Anchors
L-A-PDPAWLSUB22
TNT and THD anchors may be used in lieu of PDPA/PDPAWL powder-actuated fasteners in a one-to-one replacement for anchoring 2x wood bottom plates or cold-formed steel bottom track to concrete.
Engineering Letter
Titen HD® As a Replacement for Sill Plate Anchorage into Poured Concrete Foundation Walls
L-A-THD50WHCAN21
This letter confirms that the THD50600WH is structurally acceptable as an anchorage substitute for code-prescribed ½"-diameter anchor bolts in building frames using 2x sill plates.
Engineering Letter
3/8" Titen HD® in Fully Grouted CMU
L-A-THDGFCMU22
Simpson Strong-Tie® – 3/8" Titen HD® Heavy Duty Carbon-steel Screw Anchor Allowable Shear Loads for Anchoring into Fully Grouted CMU Construction
Engineering Letter
North Carolina Residential Code: Alternate Sill Plate Anchors
L-NCRCALTANCR22
Alternate Sill Plate Anchors for Section 4504 of the 2012 North Carolina Residential Building Code.
Engineering Letter
Titen HD® Heavy-Duty Screw Anchor Tension Loads for Tilt-Up Braces
L-A-THDTILTUP21
Simpson Strong-Tie tested 5/8”- and 3/4”-diameter carbon-steel Titen HD® heavy-duty screw anchors for tilt-up wall brace applications.
Engineering Letter
Carbon-Steel Titen HD® into Top of Fully Grouted CMU at a 3-inch Edge Distance
L-A-THDTOCMU321
This letter provides allowable loads for Simpson Strong-Tie® carbon-steel Titen HD® anchoring into the top of fully grouted CMU construction at a 3" edge distance.
Engineering Letter
Safety Data Sheet for Mechanical Anchors
SDS-MechAnchors-NA-ENG-0520
Intended to provide information for use in workplace chemical management; information such as physical properties; hazards; protective measures; precautions for handling, storing, and transportation.
SDS
Ficha de Datos de Seguridad para Anclas Mecánicas
SDS-MechAnchors-NA-ES
Diseñado para dar información útil en la gestión de químicos en el lugar de trabajo; p.ej. propiedades físicas; riesgos; medidas de protección; precauciones para manejo, almacenamiento y transporte.
SDS
Fiche de Données de Sécurité pour Ancrages Mécaniques
SDS-MechAnchors-NA-FRCA
Prévu pour fournir de l’information sur la gestion des produits chimiques au travail comme propriétés physiques, dangers, mesures de protection et précautions de manipulation, stockage et transport.
SDS
MasterFormat® Specification for Anchor Products
T-A-MSTRANCH21
Specification data for Simpson Strong-Tie Anchor products.
MasterFormat® Specification
MasterFormat® Specification for Anchor Products
T-A-MSTRANCH21
Specification data for Simpson Strong-Tie Anchor products.
MasterFormat® Specification
Simpson Strong-Tie® Suggested General Notes for Anchoring Systems (DOC)
SIMPSON-GENERAL-NOTES-AS_June2020
This comprehensive note is provided to the designer in order to specify the "design basis" post ­installed anchor products to be used on the project.
MasterFormat® Specification
Simpson Strong-Tie® Suggested General Notes for Anchoring Systems (PDF)
SIMPSON-GENERAL-NOTES-AS_June2020
This comprehensive note is provided to the designer in order to specify the "design basis" post ­installed anchor products to be used on the project.
MasterFormat® Specification

Product Information Table

Fastener Production Information and Stuff & Things
Model No. Coating/Material Size (in.) Drill Bit Dia. (in.) Wrench Size (in.) Recommended Fixture Hole Size (in.) Box Qty. Carton Qty.
Footnotes

  1. Mechanical galvanizing meets ASTM B695, Class 65, Type 1. Intended for some pressure-treated wood sill plate applications. Not for use in other corrosive or outdoor environments. See Supplemental Topics for Anchors.

  2. Models THD37134H and THD37212H do not meet minimum embedment depth requirements for strength design and require maximum installation torque of 25 ft. – lb. using a torque wrench, driver drill or cordless 1/4" impact driver with a maximum permitted torque rating of 100 ft. – lb.

  3. Length of anchor is measured from underside of head to end of anchor.
THD37300HMG Mechanically Galvanized / Carbon Steel 3/8 x 3 3/8 9/16 1/2 to 9/16 50 200
THD37400HMG Mechanically Galvanized / Carbon Steel 3/8 x 4 3/8 9/16 1/2 to 9/16 50 200
THD37500HMG Mechanically Galvanized / Carbon Steel 3/8 x 5 3/8 9/16 1/2 to 9/16 50 100
THD37600HMG Mechanically Galvanized / Carbon Steel 3/8 x 6 3/8 9/16 1/2 to 9/16 50 100
THD501200HMG Mechanically Galvanized / Carbon Steel 1/2 x 12 1/2 3/4 5/8 to 11/16 5 20
THD50400HMG Mechanically Galvanized / Carbon Steel 1/2 x 4 1/2 3/4 5/8 to 11/16 20 80
THD50500HMG Mechanically Galvanized / Carbon Steel 1/2 x 5 1/2 3/4 5/8 to 11/16 20 80
THD50600HMG Mechanically Galvanized / Carbon Steel 1/2 x 6 1/2 3/4 5/8 to 11/16 20 80
THD50612HMG Mechanically Galvanized / Carbon Steel 1/2 x 6 1/2 1/2 3/4 5/8 to 11/16 20 40
THD50800HMG Mechanically Galvanized / Carbon Steel 1/2 x 8 1/2 3/4 5/8 to 11/16 20 40
THD75100HMG Mechanically Galvanized / Carbon Steel 3/4 x 10 3/4 1 1/8 7/8 to 15/16 5 10
THD75500HMG Mechanically Galvanized / Carbon Steel 3/4 x 5 3/4 1 1/8 7/8 to 15/16 5 20
THD75812HMG Mechanically Galvanized / Carbon Steel 3/4 x 8 1/2 3/4 1 1/8 7/8 to 15/16 5 10
THDB62500HMG Mechanically Galvanized / Carbon Steel 5/8 x 5 5/8 15/16 3/4 to 13/16 10 40
THDB62600HMG Mechanically Galvanized / Carbon Steel 5/8 x 6 5/8 15/16 3/4 to 13/16 10 40
THDB62612HMG Mechanically Galvanized / Carbon Steel 5/8 x 6 1/2 5/8 15/16 3/4 to 13/16 10 40
THDB62800HMG Mechanically Galvanized / Carbon Steel 5/8 x 8 5/8 15/16 3/4 to 13/16 10 20
THDT75600HMG Mechanically Galvanized / Carbon Steel 3/4 x 6 3/4 1 1/8 7/8 to 15/16 5 20
THD37134H Zinc Plated / Carbon Steel 3/8 x 1 3/4 3/8 9/16 1/2 to 9/16 50 250
THD37212H Zinc Plated / Carbon Steel 3/8 x 2 1/2 3/8 9/16 1/2 to 9/16 50 200
THD37300H Zinc Plated / Carbon Steel 3/8 x 3 3/8 9/16 1/2 to 9/16 50 200
THD37400H Zinc Plated / Carbon Steel 3/8 x 4 3/8 9/16 1/2 to 9/16 50 200
THD37500H Zinc Plated / Carbon Steel 3/8 x 5 3/8 9/16 1/2 to 9/16 50 100
THD37600H Zinc Plated / Carbon Steel 3/8 x 6 3/8 9/16 1/2 to 9/16 50 100
THD501200H Zinc Plated / Carbon Steel 1/2 x 12 1/2 3/4 5/8 to 11/16 5 20
THD501300H Zinc Plated / Carbon Steel 1/2 x 13 1/2 3/4 5/8 to 11/16 5 20
THD501400H Zinc Plated / Carbon Steel 1/2 x 14 1/2 3/4 5/8 to 11/16 5 20
THD501500H Zinc Plated / Carbon Steel 1/2 x 15 1/2 3/4 5/8 to 11/16 5 20
THD50300H Zinc Plated / Carbon Steel 1/2 x 3 1/2 3/4 5/8 to 11/16 25 100
THD50400H Zinc Plated / Carbon Steel 1/2 x 4 1/2 3/4 5/8 to 11/16 20 80
THD50500H Zinc Plated / Carbon Steel 1/2 x 5 1/2 3/4 5/8 to 11/16 20 80
THD50600H Zinc Plated / Carbon Steel 1/2 x 6 1/2 3/4 5/8 to 11/16 20 80
THD50612H Zinc Plated / Carbon Steel 1/2 x 6 1/2 1/2 3/4 5/8 to 11/16 20 40
THD50800H Zinc Plated / Carbon Steel 1/2 x 8 1/2 3/4 5/8 to 11/16 20 40
THD75100H Zinc Plated / Carbon Steel 3/4 x 10 3/4 1 1/8 7/8 to 15/16 5 10
THD75400H Zinc Plated / Carbon Steel 3/4 x 4 3/4 1 1/8 7/8 to 15/16 10 40
THD75500H Zinc Plated / Carbon Steel 3/4 x 5 3/4 1 1/8 7/8 to 15/16 5 20
THD75700H Zinc Plated / Carbon Steel 3/4 x 7 3/4 1 1/8 7/8 to 15/16 5 10
THD75812H Zinc Plated / Carbon Steel 3/4 x 8 1/2 3/4 1 1/8 7/8 to 15/16 5 10
THDB25178H Zinc Plated / Carbon Steel 1/4 x 1 7/8 1/4 3/8 3/8 to 7/16 100 500
THDB25234H Zinc Plated / Carbon Steel 1/4 x 2 3/4 1/4 3/8 3/8 to 7/16 50 250
THDB25300H Zinc Plated / Carbon Steel 1/4 x 3 1/4 3/8 3/8 to 7/16 50 250
THDB25312H Zinc Plated / Carbon Steel 1/4 x 3 1/2 1/4 3/8 3/8 to 7/16 50 250
THDB25400H Zinc Plated / Carbon Steel 1/4 x 4 1/4 3/8 3/8 to 7/16 50 250
THDB62100H Zinc Plated / Carbon Steel 5/8 x 10 5/8 15/16 3/4 to 13/16 10 20
THDB62400H Zinc Plated / Carbon Steel 5/8 x 4 5/8 15/16 3/4 to 13/16 10 40
THDB62500H Zinc Plated / Carbon Steel 5/8 x 5 5/8 15/16 3/4 to 13/16 10 40
THDB62600H Zinc Plated / Carbon Steel 5/8 x 6 5/8 15/16 3/4 to 13/16 10 40
THDB62612H Zinc Plated / Carbon Steel 5/8 x 6 1/2 5/8 15/16 3/4 to 13/16 10 40
THDB62800H Zinc Plated / Carbon Steel 5/8 x 8 5/8 15/16 3/4 to 13/16 10 20
THDT75600H Zinc Plated / Carbon Steel 3/4 x 6 3/4 1 1/8 7/8 to 15/16 5 20

Product Information Tables

Titen HD® Anchor Product Data — Zinc Plated
Size (in.) Model No. Drill Bit Dia. (in.) Wrench Size (in.) Quantity
Box Carton
1/4 x 1 7/8 THDB25178H 1/4 3/8 100 500
1/4 x 2 3/4 THDB25234H 1/4 3/8 50 250
1/4 x 3 THDB25300H 1/4 3/8 50 250
1/4 x 3 1/2 THDB25312H 1/4 3/8 50 250
1/4 x 4 THDB25400H 1/4 3/8 50 250
3/8 x 1 3/4 THD37134H* 3/8 9/16 50 250
3/8 x 2 1/2 THD37212H* 3/8 9/16 50 200
3/8 x 3 THD37300H 3/8 9/16 50 200
3/8 x 4 THD37400H 3/8 9/16 50 200
3/8 x 5 THD37500H 3/8 9/16 50 100
3/8 x 6 THD37600H 3/8 9/16 50 100
1/2 x 3 THD50300H 1/2 3/4 25 100
1/2 x 4 THD50400H 1/2 3/4 20 80
1/2 x 5 THD50500H 1/2 3/4 20 80
1/2 x 6 THD50600H 1/2 3/4 20 80
1/2 x 6 1/2 THD50612H 1/2 3/4 20 40
1/2 x 8 THD50800H 1/2 3/4 20 40
1/2 x 12 THD501200H 1/2 3/4 5 25
1/2 x 13 THD501300H 1/2 3/4 5 25
1/2 x 14 THD501400H 1/2 3/4 5 25
1/2 x 15 THD501500H 1/2 3/4 5 25
5/8 x 4 THDB62400H 5/8 15/16 10 40
5/8 x 5 THDB62500H 5/8 15/16 10 40
5/8 x 6 THDB62600H 5/8 15/16 10 40
5/8 x 6 1/2 THDB62612H 5/8 15/16 10 40
5/8 x 8 THDB62800H 5/8 15/16 10 20
3/4 x 4 THD75400H 3/4 1 1/8 10 40
3/4 x 5 THD75500H 3/4 1 1/8 5 20
3/4 x 6 THDT75600H 3/4 1 1/8 5 20
3/4 x 7 THD75700H 3/4 1 1/8 5 10
3/4 x 8 1/2 THD75812H 3/4 1 1/8 5 10
3/4 x 10 THD75100H 3/4 1 1/8 5 10
* These models do not meet minimum embedment depth requirements for strength design and require maximum installation torque of 25 ft. – lb. using a torque wrench, driver drill or cordless 1/4" impact driver with a maximum permitted torque rating of 100 ft. – lb.
Titen HD® Anchor Product Data — Mechanically Galvanized
Size (in.) Model No. Drill Bit Dia. (in.) Wrench Size (in.) Quantity
Box Carton
3/8 x 3 THD37300HMG 3/8 9/16 50 200
3/8 x 4 THD37400HMG 50 200
3/8 x 5 THD37500HMG 50 100
3/8 x 6 THD37600HMG 50 100
1/2 x 4 THD50400HMG 1/2 3/4 20 80
1/2 x 5 THD50500HMG 20 80
1/2 x 6 THD50600HMG 20 80
1/2 x 6 1/2 THD50612HMG 20 40
1/2 x 8 THD50800HMG 20 40
5/8 x 5 THDB62500HMG 5/8 15/16 10 40
5/8 x 6 THDB62600HMG 10 40
5/8 x 6 1/2 THDB62612HMG 10 40
5/8 x 8 THDB62800HMG 10 20
3/4 x 6 THDT75600HMG 3/4 1 1/8 5 20
3/4 x 8 1/2 THD75812HMG 5 10
3/4 x 10 THD75100HMG 5 10
Mechanical galvanizing meets ASTM B695, Class 65, Type 1. Intended for some pressure-treated wood sill plate applications. Not for use in other corrosive or outdoor environments. See Supplemental Topics for Anchors or visit www.strongtie.com/info for more corrosion information.
Titen HD® Anchor Product Data — Stainless Steel
Size (in.) Model No. Drill Bit Dia. (in.) Wrench Size (in.) Quantity
Box Carton
3/8 x 3 THD37300H6SS 3/8 9/16 50 200
3/8 x 4 THD37400H6SS 3/8 9/16 50 200
3/8 x 5 THD37500H6SS 3/8 9/16 50 100
3/8 x 6 THD37600H6SS 3/8 9/16 50 100
1/2 x 3 THD50300H6SS 1/2 3/4 25 100
1/2 x 4 THD50400H6SS 1/2 3/4 20 80
1/2 x 5 THD50500H6SS 1/2 3/4 20 80
1/2 x 6 THD50600H6SS 1/2 3/4 20 80
1/2 x 6 1/2 THD50612H6SS 1/2 3/4 20 40
1/2 x 8 THD50800H6SS 1/2 3/4 20 40
5/8 x 4 THDB62400H6SS 5/8 15/16 10 40
5/8 x 5 THDB62500H6SS 5/8 15/16 10 40
5/8 x 6 THDB62600H6SS 5/8 15/16 10 40
5/8 x 6 1/2 THDB62612H6SS 5/8 15/16 10 40
5/8 x 8 THDB62800H6SS 5/8 15/16 10 20
3/4 x 4 THD75400H6SS 3/4 1 1/8 10 40
3/4 x 5 THD75500H6SS 3/4 1 1/8 5 20
3/4 x 6 THD75600H6SS 3/4 1 1/8 5 20
3/4 x 7 THD75700H6SS 3/4 1 1/8 5 10
3/4 x 8 1/2 THD75812H6SS 3/4 1 1/8 5 10
Additional Installation Information
Titen HD® Diameter (in.) Wrench Size (in.) Recommended Fixture Hole Size (in.) Min. Hole Depth Overdrill (in.)
1/4 3/8 3/8 to 7/16 1/8
3/8 9/16 1/2 to 9/16 1/4
1/2 3/4 5/8 to 11/16 1/2
5/8 15/16 3/4 to 13/16 1/2
3/4 1 1/8 7/8 to 15/16 1/2

Code Reports & Compliance

Drawings

PDF DWG DXF RFA IFC SAT

Related Products